Thermoscreens C series Скачать руководство пользователя страница 16

 

4001160-6 UK 

 

Page 16 of 16 

 

 

 

 

 

Service & Maintenance 

 

Always disconnect and isolate the mains electricity supply before installing, 
maintaining or repairing this equipment.  Note: All maintenance/repairs should 
only be carried out by a competent electrician or Thermoscreens appointed 
technician.  

 

Once the mains supply is isolated, remove end caps from the air curtain (if fitted).  
Remove each air intake grille by unfastening two screws on each grille - M4 x 10mm 
Pozi No.2 screws accessed via the larger hole at the bottom of each grille. 

 

To ensure the air curtain operates at full efficiency the inlet/outlet grilles, fan impellers, 
housings and motors must be kept free of dust and debris.  Build up of dust on the fan 
impellers can cause vibration, noise and excessive wear on the motor bearings. 

 

Frequency of cleaning will depend on the environment, but we would recommend that 
the unit be cleaned a minimum of every 3 months (failure to adequately maintain the 
unit and provide a suitable cleaning schedule will result in performance degradation 
and reduce the life expectancy of the air-curtain). 

 

Vacuum and clean the build-up of dirt and debris within the air-curtain 

(please note 

that the motor(s) are permanently lubricated and require no additional lubrication). 
If filters are fitted, ensure these are regularly inspected and cleaned or replaced.  All 
dirty or blocked filters should be immediately replaced. 

 

Once the air curtain has been cleaned check all electrical connections within the unit 
ensuring terminals are tight and that crimped connections have not become loose. 
Refit inlet grilles and end caps.  Reconnect the electrical supply and fully function test 
the air-curtain to ensure correct operation (See Commissioning). 

 

If the outer casing requires cleaning this should be done using a warm soft cloth. 
Do not use solvents or abrasive materials. 

 

 

 Warranty 

 

If any problems are encountered, please contact your installer/supplier.  Failing this 
please contact the Thermoscreens warranty department.  All units are covered by a two 
year warranty period. 

 

Care has been taken in compiling these instructions to ensure they are correct, although 
Thermoscreens disclaims all liability for damage resulting from any inaccuracies and/or 
deficiencies in this documentation.  Thermoscreens retain the right to change the 
specifications stated in these instructions. 

 

Thermoscreens Ltd  

 

 

 

 

 

St. Mary’s Road  Nuneaton 
Warwickshire  England  
CV11 5AU 

   

 

 

 

 

 

Email: 

[email protected]

 

Tel:  + 44 (0) 24 7638 4646 
Fax: + 44 (0) 24 7638 8578 

www.thermoscreens.com

 

Содержание C series

















Отзывы: