thermofin TCS.2 Series Скачать руководство пользователя страница 8

Страница: 8 / 162

Controller operating manual

15.11.2020 – Version 1.1

TCS.2 series –

thermofin

control system 2

generation

Page: 8/162

Operating manual - translation into English © thermofin GmbH

1. GENERAL INFORMATION

The operating manual serves for optimal handling and parametrization of the TCS.2. It should enable

the user to adjust the system to be controlled according to ecological and economic aspects and to

guarantee trouble-free use.

Attention:

Read and follow the safety instructions in the device manual before use.

Principles

This operating manual refers to devices of the following series:



TCS.2: thermofin

control system, 2

generation

and on all related device components supplied by the manufacturer. Regardless of whether wired or

unwired or whether defined as a standard or a special solution with the additional designation “X”.

The binding technical data can be found in the currently valid catalogue sheets, the associated device

specifications and the information on the corresponding nameplates.

For control cabinets, control and regulating devices, the information on their identification plates

applies primarily.

Introduction

Dry coolers, condensers and evaporators require a correspondingly complex control system for

optimal performance adjustment to the currently dissipated heat or amount of cold, taking into

account the climatic environmental conditions. Modern control systems not only enable an operating

mode that is precisely adapted to the conditions of the cooling systems, they are also characterized

by a particularly high level of energy efficiency. Helpful additional functions increase the ease of use

of the systems and enable fast communication with higher-level control systems. The use of high-

quality components enables the fans to run absolutely smoothly as well as gentle and trouble-free

handling of the fan drives.

Complete or split systems are available to users for such control tasks.

The complete systems for fan drives have compact units, each consisting of a control, regulation and

power section.

The split systems are separate units for the control and regulation tasks as well as for the power-

side control of the fan motors.

The split systems are mainly used for fan drives in which the power section is already integrated in

the motor housing or the drive concept and the like provides a separate inverter or voltage regulator.

Содержание TCS.2 Series



































































































































































Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды

thermofin TCS.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды