thermofin TCS.2 Series Скачать руководство пользователя страница 54

Страница: 54 / 162

Controller operating manual

15.11.2020 – Version 1.1

TCS.2 series –

thermofin

control system 2

generation

Page: 54/162

Operating manual - translation into English © thermofin GmbH

Control of ZA Modbus

wireless

Setpoint, status and fault messages are transmitted via Modbus. All

registers are written and read according to Ziehl-Abegg

specifications. The data transfer is realized by the TCS wireless

system instead of a signal cable. For setting the communication

parameters, see chapter 4.5 “

BMS (Building management system

)

bus system”.

0 – 10 V DC control

The setpoint is transmitted via an analogue 0 - 10 V DC standard

signal. The alarm relay outputs of the fans are connected to a digital

input. With up to 4 fans this is possible on the TCS basic unit (DI-5

to DI-8), see also chapter 4.3.1 “

Digital IN basic unit”.

With more

than 4 fans, no digital inputs are used on the TCS basic unit; one or

more digital CAN extensions are used instead (see also chapter

4.3.5

“IN / OUT extensions

”).

Step switching

Unregulated AC fans are used which are controlled in up to 12

levels with a contactor circuit via digital outputs. With up to 4 fan

groups or external fault inputs, this is this is possible on the TCS

basic unit (DI-5 to DI-8), see also chapter 4.3.1 “

Digital IN basic

unit”.

With more than 4 external fault inputs, no digital inputs are

used on the TCS basic unit; one or a maximum of two digital CAN

extensions are used instead (see also chapter 4.3.5

“IN / OUT

extensions”).

* Factory setting

Direction of rotation

This function enables the user to blow away leaves or other contaminants from the heat exchanger

by reversing the direction of rotation of the fans. It is controlled via a terminal or bus. See also chapter

4.2.9 “

Reversion of rotation control”

or 5.6.6 “

Speed reversion of rotation (ROR)”.

The following two options are available:

Clockwise rotation in normal operation. As soon as “Reversion of rotation” is

activated,

the fan rotates to the left.

Counter-clockwise rotation in normal operation. As soon as “Reversion of

rotation” is activated,

the fan rotates to the right.

* Factory setting

Содержание TCS.2 Series



































































































































































Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды

thermofin TCS.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание TCS.2 Series

Отзывы:

Похожие инструкции для TCS.2 Series

Бренды по названию

Популярные бренды