Thermo 3307 Скачать руководство пользователя страница 41

Страница: 41 / 57

Steri-Cult Incubator ____________________________________________________________________________Servicing

11-2

11.2 Replacing the Fuses

Refer to Wiring Diagram 3307-71, page 1 of 2, Fuse Holder
Detail 2.

The following procedure requires accessing the
electronics area. Qualified personnel only should
perform this procedure. Wearing a electrostatic
discharge wrist band or other grounding device is
recommended.

To access the only replaceable fuse in the incubator, follow

the steps below.

1. Turn off the incubator’s power switch and disconnect the

power cord.

2. Remove the four screws from the left side panel. Set the

panel aside.

3. On the left side of the opening is the electronics area.

Locate the fuse. See Table 11-1 below for replacement
fuse specifications. Replace the blown fuse with a new
one.

4. Install the panel and secure with the screws.

5. Return the unit to service. If the fuse blows after restor-

ing power to the incubator, contact the Technical
Services Department.

11.3 Replacing the CO

and RH Air Filters

The CO

and RH air filters are recommended to be

replaced annually. Follow the steps below to replace the filters.

1. Turn off the incubator’s power switch and disconnect the

power cord.

2. Remove the four screws from the left side panel. Set the

panel aside.

3. On the left side of the opening is the electronics area.

Locate the CO

air filter (Figure 11-1). Disconnect care-

fully from the tubing and replace.

5. In the right side of the opening is the humidity system.

Locate the RH air filter in the upper right corner (Figure
11-2). Disconnect from the tubing and replace.

6. Install the panel and secure with the screws.

7. Return the unit to service.

Fuse Voltage

Manufacturers Part #

Amperage

Rating

Rupture

Speed

IEC

Letter

Code

115VAC ACC

BUSS GMC-1.0A

1.0 Amp

Time-Lag

250VAC ACC

BUSS GMC-740ma

750mAmp

Time-Lag

230VAC ACC

BUSS GMC-500ma

0.5 Amp

Time-Lag

Table 11-1, Fuse Replacement Chart

Figure 11-1

Figure 11-2

Содержание 3307


























































Результаты поиска

Содержание 3307

Отзывы:

Бренды по названию

Популярные бренды

Thermo 3307, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 3307

Отзывы:

Бренды по названию

Популярные бренды