manualshive.com logo in svg

Thermo 3307, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Thermo 3307 Скачать руководство пользователя страница 19

k.  Setting a High RH Alarm Limit (tracking alarm)

The high RH alarm limit is the deviation from the humidity

setpoint which causes a high RH alarm.  The setpoint is vari-
able from 5 to 20% RH  The factory setting is 10% RH. When
the alarm is activated, the humidity system is disabled.

1. Press the Mode key until the Configuration indicator

lights.

2. Press the right arrow until RH HI LMT XX  is displayed

in the message center.

3. Press up/down arrow to change the RH high alarm limit.

4. Press Enter to save the RH high alarm limit.

5. Press the Mode key to return to Run mode or right/left

to go to next/previous parameter.

l.  Enabling RH Alarms to Trip Contacts

The high and low RH alarms can be programmed to trip

the remote alarm contacts.  A setting of ON activates this abili-
ty. A setting of OFF will not allow the RH alarm to trip the con-
tacts.  The factory setting is ON.

1. Press the Mode key until the Configuration indicator

lights.

2. Press the right arrow until RH RELAY ON/OFF is dis-

played in the message center.

3. Press up/down arrow to toggle the setting ON or OFF.

4. Press Enter to save the setting.

5. Press the Mode key to return to Run mode or right/left

to go to next/previous  parameter.

m.  Selecting a Primary Tank w/ Gas Guard Option

On units equipped with the Gas Guard option, a primary

tank can be selected.  The primary tank will be either Tank 1 or
2.  The factory setting is Tank1.

1. Press the Mode key until the Configuration indicator

lights.

2. Press the right arrow until TANK SELECT X is dis-

played in the message center.

3. Press up/down arrow to toggle setting between 1 and 2 .

4. Press Enter to save the setting.

5. Press the Mode key to return to Run mode or right/left

to go to next/previous parameter.

Steri-Cult Incubator ______________________________________________________________________Configuration

4 - 3

n.  Disabling the Gas Guard System

On units equipped with the Gas Guard option, the Gas

Guard system may be turned ON or OFF if it is not in use.  The
factory setting is ON.

1. Press the Mode key until the Configuration indicator

lights.

2. Press the right arrow until GAS GUARD ON/OFF is

displayed in the message center.

3. Press up/down arrow to toggle the setting ON or OFF.

4. Press Enter to save the setting.

5. Press the Mode key to return to Run mode or right/left

to go to next/previous parameter.

o.  Setting a RS485 Communications Address 
(1535 compatible only)

On units that have the RS485 option, direct communication

with the Model 1535 alarm system can be established. Each
piece of equipment connected to the Model 1535 must have a
unique address. An address of 0-24 can be entered for the incu-
bator. A setting of 0 is an invalid address that the 1535 will
ignore. The factory setting for the RS485 address is 0.

1. Press the Mode key until the Configuration indicator

lights.

2. Press the right arrow until 485 ADDRESS XX is dis-

played in the message center.

3. Press up/down arrow to move the RS485 address.

4. Press Enter to save the RS485 address.

5. Press the Mode key to return to Run mode or right/left

to go to next/previous parameter.

Содержание 3307


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды