manualshive.com logo in svg

Thermo 3307, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Thermo 3307 Скачать руководство пользователя страница 25

Section 6 - Troubleshooting

Certain conditions can occur in usage of this incubator

which can be resolved by checking the troublshooting chart
below. If the issue is not listed or cannot be resolved, contact
the Services department.

Problem

Possible Cause

Solution

Poor temperature recovery and/or

1. HEPA filter is dirty

1. If the HEPA filter is older than six 

temperature overshoot.

2. Temperature probe not reinstalled

months, replace with new.

correctly.

2. Ensure temperature probe holder 

bottoms-out in hole.

Poor CO

2

recovery and/or

1. CO

2

sensor not reinstalled correctly.

1. Ensure CO

2

sensor bottoms-out in hole.

actual higher than display.

Poor RH recovery.

1. Access port is plugged.

1. Install access port filter assembly.  If it is

older than six months, replace with new.

2. Humidifier tubing pinched or

2. Check to ensure tubing is not pinched or 

disconnected.

disconnected.

3. Humidifier has heavy build-up.

3. Clean the humidifier; see Section 6.3.

4. RH sensor not reinstalled correctly.

4. Ensure RH sensor bottoms out in hole.

Condensation on cabinet face.

1. Removable gasket not reinstalled 

1. Ensure there are not gaps between the 

properly.

gasket and the glass door.

Condensation on cabinet interior. 

1. RH out of calibration.

1. Calibrate the RH, see Section 3.1c.

Condensation will also increase water 

2. RH sensor not reinstalled correctly.

2. Ensure RH sensor bottoms-out in hole.

consumption. Under normal conditions
of 37°C, 95% RH, 5% CO

2

, five door 

openings per day, the water bottle should 
last 2-3 weeks.

Steri-Cult Incubator ________________________________________________________________________Troubleshooting

6 - 1

Содержание 3307


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды