Thermo Scientific Thermo Scientific HyPerforma DS 300 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 55

background image

3. Remove the drive shafts from the crate and set them aside.

Depending on the size and number of drive shafts ordered, they
may be secured to the bottom of the crate. Longer drive shafts will
be secured upright in a front corner of the crate.

4. Remove the uncrating instructions from the plastic sleeve affixed

to the inside wall of the crate.

5. Remove the small cardboard box containing the tools. Unwrap the

tools and set them aside.

6. Remove the strap that secures the mixer to the top of the crate

(Figure 2.3).

Figure 2.3. Removing the

strap securing the mixer to

the top of the crate

7. Remove the strap that secures the mixer to the eyes screwed into

the bottom of the crate (Figure 2.4).

Figure 2.4. Removing the

bottom strap

Thermo Scientific

Chapter 2

|

Setup and operating information

HyPerforma DS 300 Single‑Use Mixer User's Guide

|

18

«
...
19
20
21
22
23
...
»

Содержание Thermo Scientific HyPerforma DS 300
























































Отзывы:

Нет отзывов

Похожие инструкции для Thermo Scientific HyPerforma DS 300

Бренд: ABB Страницы: 6

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Makita Страницы: 84

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: R.M. Young Страницы: 10

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: TANDBERG Страницы: 23

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Teac Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды