Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя | Manualshive

Страница: 67 / 148

background image

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

57

13

Basic Concentration Measurements—Basic
A-%T-C

This chapter covers:

•

Basic Concentration Measurements

•

Using Conc/Std to Measure Concentration

•

Using Conc/Factor to Measure Concentration

•

Measuring Samples

Basic Concentration Measurements

Use Basic ATC mode to make basic concentration measurements. This basic concentration
mode is useful for very simple comparisons that do not require a standard curve. You cannot
save data in this application or factors used when a single standard is measured. For better
accuracy and the ability to save and recall methods and data, use the Standard Curve
application mode described in

“Concentration Measurements—Standard Curve Application”

.

Measuring concentration using the Basic ATC mode is similar to measuring Absorbance or
%T. Basic ATC mode lets you measure concentration using either a factor or one standard to
convert absorbance readings to concentration units.

• When using a factor, specify the factor and concentration units.

• When using a standard, specify the concentration of the standard and measure its

absorbance.

When Basic ATC is set to Conc/Std or Conc/Factor, you can perform these tasks.

•

Setting the Wavelength and Mode

•

Measuring a Blank

• Measuring a standard or entering a factor

•

Measuring Samples

«
...
65
66
67
68
69
...
»

Содержание Orion AquaMate 7000 Vis





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion AquaMate 7000 Vis

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: DAE Страницы: 28

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

EXTREME DUTY TPMS

Бренд: Valor Страницы: 2

Бренд: WAGO Страницы: 96

Бренд: Danfoss Страницы: 80

Бренд: Magtrol Страницы: 76

Бренд: Flexim Страницы: 160

Бренд: Neriox Страницы: 10

Бренд: JensPrima Страницы: 20

SoundExpert LxT

Бренд: Larson Davis Страницы: 307

Бренд: D-tect Systems Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды