Thermo Scientific MaxQ 2000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 34

background image

MaxQ 2000 Shaker

5-1

Thermo Scientific

Section 5

Maintenance

Wash the exterior of the unit with a soft cloth using a solution of mild
soap and water, rinse off with clean water and dry thoroughly.

Warning

To avoid risk of electric shock, disconnect equipment from

power source before performing any maintenance.

s

1. Remove the platform by loosening the 4 thumbscrews, remove ribbed

mat, remove the 9 smaller screws on the platform mounting plate,
there are 3 Phillips screws at each of the 3 bearing mounts.

2. Position the platform mounting plate atop the shaker body and install

all 9 screws by hand until they are finger-tight only. Rotate the speed
control fully counterclockwise (OFF) and plug the unit into an outlet.
Rotate the speed control knob slowly in the clockwise direction to
allow the shaker to orbit at its slowest speed.

Note

While adjusting the platform retaining screws, make certain lid

switch, located at back of chamber, is activated (pressed in).

3. While it is slowly orbiting, slightly tighten each of the A screws in

Figure 1. Repeat this procedure by slightly tightening all the B screws,
then complete procedure by tightening the C screws.

Replacing Platform

Mounting Plate

Figure 5-1.

Platform Mounting Plate

«
...
22
23
24
25
26
...
»

Содержание MaxQ 2000



































Отзывы:

Нет отзывов

Похожие инструкции для MaxQ 2000

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: ACCU-CHECK Страницы: 104

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды