Thermo Scientific iCAP 7000 Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 72

background image

iCAP Customer Familiarisation Manual

Page 68 of 72

This document is part numbered 849940090071

Version 1.02

10.5.3 Solid deposit in sample capillary

Note: This step assumes that a passage still exists through the
contaminating material (i.e. the tip is not entirely clogged).

Try to deduce the chemical nature of the deposit from the type of samples that are
being analysed and select the solvent most likely to dissolve it. Inject the solvent
into the nozzle with a plastic dropper or squeeze bottle until the affected area is
filled. Expel the solvent with compressed gas. Refill and expel the solvent
repeatedly. Examine the nebuliser under magnification. If the material is gone, rinse
the nebuliser with isopropyl alcohol and dry thoroughly

.

Immerse the nozzle in a rinse solution. Warm the solution for stubborn deposits.
Follow with a rinse of pure solvent, then isopropyl alcohol and dry thoroughly.

If the deposit remains after prolonged soaking, apply pressurised gas at the
appropriate input(s) to help force the deposit away.

10.5.4 Organic matter

Immerse the nozzle of your nebuliser in a hot cleaning solution of chromic and
sulphuric acids at 100ºC

.

Caution: This solution is corrosive, use suitable precautions

Allow the solution to rinse into the passages of the nebuliser until the affected area
is filled. Expel and replace the solution at intervals until the deposit is gone or until
the chromium reduction (green colour) ceases. Rinse the nebuliser thoroughly with
water, then with isopropyl alcohol and dry completely.

«
...
66
67
68
69
70
...
»

Содержание iCAP 7000 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для iCAP 7000 Series

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Garmin Страницы: 20

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Idmed Страницы: 2

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: Rowlinson Garden Products Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды