Thermo Scientific iCAP 7000 Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 72

background image

iCAP Customer Familiarisation Manual

Page 23 of 72

This document is part numbered 849940090071

Version 1.02

7.2 Example Standard Operating Procedures

This method setup procedure, which by no means covers all the possible parameters used in
Qtegra, should be enough for setting up a basic analysis. It is recommended that the user reads
the iCAP software manual for more advanced use of the system.

7.3 Preparing the System

Turn Argon Gas on at Cylinder and set for 0.55 MPa (5.5 BAR) pressure on gauge near
instrument
Turn on the purge gas if separate
Note: for normal use gas should be left purging constantly

▲

Turn on the air supply for the Additional gas supply (7600 only) if used.
Switch on power to iCAP Spectrometer.
Note: for normal use power should be left on constantly.

▲

Switch on Water Chiller
Push Platen on to rollers of pump by way of the 4 (3) pressure screws
Make sure the drain tube is placed in an open neck vessel
Place sample tube in a blank solution
Switch on computer
Click on the Qtegra Icon on the computer desktop.

7.4 Striking the Plasma

Click on Qtegra to open the program.

7.4.1 Interlocks

Check the interlocks are all green and take appropriate action if any are RED

«
...
21
22
23
24
25
...
»

Содержание iCAP 7000 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для iCAP 7000 Series

Бренд: Cadman Страницы: 66

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

Бренд: Bang & Olufsen Страницы: 2

Бренд: Fellowes Страницы: 20

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: Zero88 Страницы: 26

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Бренд: NEBO Страницы: 2

SystemRoMedic RiseAtlas450

Бренд: Handicare Страницы: 48

Allen-Bradley PowerFlex 755T Flux Vector Tuning

Бренд: Rockwell Automation Страницы: 116

Бренд: OmniCure Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды