Thermo Electron 3-Star Conductivity Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 111

background image

Thermo Electron Corporation

VIII-2

Orion Star Series Meter

Dissolved Oxygen

DO % Saturation Resolution:

This selects the displayed resolution in

measurement mode. In addition the resolution selection is used by Thermo Orion’s
SMART STABILITY & SMART AVERAGING algorithms to optimize the accuracy,
precision, and response of the DO measurement.

DO (mg/L) Concentration Resolution:

This selects the displayed resolution in

measurement mode. In addition the resolution selection is used by Thermo Orion’s
SMART STABILITY & SMART AVERAGING algorithms to optimize the accuracy,
precision, and response of the DO measurement.

DO Barometric Pressure Compensation Selection:

This selects whether

to use the instruments internal barometer for pressure compensation or use a
manually set pressure. In general we recommend using the internal barometer, but
you may wish to use manual pressure compensation if you are measuring DO with
a submerged probe or in a pressurized vessel where the probe is exposed to higher
pressures then the meter.

DO Manual Pressure Setting:

This screen will only appear if Manual Barometric

Pressure compensation has been selected.  This is where you enter the pressure to
use for pressure compensating the DO measurement.  The pressure in entered in
mm of Hg (Mercury).  See the following table to convert from other units
of pressure.

hPa (mBar)

mm Hg (torr)

Inches Hg

lbf/in2 (PSI)

1 hPa (mBar)

1

0.75006

0.02953

0.014504

1 mm Hg (torr)

1.3332

1

0.039370

0.019337

1 Inches Hg

33.864

25.400

1

0.491154

1 lbf/in2 (PSI)

68.9475

51.7149

2.03602

1

Example:

To convert 14.1 PSI to mm Hg, multiple 14.7 by 51.7149 to get

750.21 mm Hg.

DO Salinity Correction Selection:

This screen will only be shown on meters

that have conductivity as well as DO.  The Automatic setting takes the conductivity
reading to calculate the salinity correction factor and automatically applies that to
the DO measurement.  A conductivity probe must be used in addition to the DO
probe for automatic salinity correction.  The manual setting allow the user to enter
a manual salinity correction factor.  Select the Manual setting and set it to zero to
disable salinity correction.

«
...
58
59
60
61
62
...
»

Содержание 3-Star Conductivity
















































































































Отзывы:

Нет отзывов

Похожие инструкции для 3-Star Conductivity

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: E Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: OHAUS Страницы: 19

Бренд: OHAUS Страницы: 54

Бренд: Zenner Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Бренд: LaserLiner Страницы: 64

Бренд: Proteus Страницы: 4

Бренд: Major tech Страницы: 16

Бренд: Vanguard Instruments Страницы: 85

WTW pH/ION 3310

Бренд: Xylem Страницы: 48

Бренд: Hanna Страницы: 44

Бренд: Hauber Elektronik Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды