manualshive.com logo in svg

Thermo Electron 3-Star Conductivity, Руководство пользователя

Поделиться
Скачать
Thermo Electron 3-Star Conductivity Скачать руководство пользователя страница 15

II-3

Orion Star Series Meter

Thermo Electron Corporation

Introduction

•  The pH, ISE and ORP combination and sensing electrodes have a waterproof 

BNC connector. These are connected to the metal BNC post. 

•  Automatic Temperature Compensation (ATC) probes are inserted into the 

waterproof 8 pin MiniDIN Connector. 

•  Benchtop meters have a pin tip jack for a separate reference electrode. These 

require an appropriate BNC sensing electrode for measurement. 

•  Conductivity probes use the waterproof 8 pin MiniDIN connector. All Orion  

Star series 2- and 4- electrode cell conductivity probes have built-in  
temperature sensors. 

•  The DO autostir probe uses the waterproof 9 pin MiniDIN connector and the 

stirrer jack for the smaller probe connector. 

Note:  

The 9708 DO electrode can be used with the BNC connector.  

▲

Non-glass ISFET pHuture® MMS™ sensors for pH, ORP and temperature use the 
waterproof 9 pin MiniDIN connector. The pH/ORP,conductivity and temperature 
Pentrode™ (6175MD) uses both the waterproof 9 pin MiniDIN and waterproof 8 pin 
MiniDIN connectors.

Turning On the Instrument

With the batteries installed in the portable meters or either the batteries installed 
or line power attached to the benchtop meter, press the Power Key to turn on the 
instrument.  A quick press of the Power Key after the meter has powered up will 
toggle the backlight on & off.  If the meter is on battery power then the backlight will 
automatically turn off after 2 minutes to save battery life.  If the low Bat is displayed 
you will no longer be able to turn on the backlight until the batteries are replaced. 
If you benchtop is on line power then the backlight will stay on until turned off with 
the power/backlight key.  To turn off the meter press and hold the power button for 
3 seconds.

Содержание 3-Star Conductivity
















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды