Thermann TH28ENR6L Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

background image

Thermann Installer's Manual
Gas Continuous Flow Water Heaters

Connecting the Quick Connect Cord to the two units.

1. Turn off the power.
2. Remove the front cover of the heater (4 screws).
3. Pass the Quick Connect Cord through the wiring throughway and into the unit.
4. Plug the connector on the Quick Connect Cord to the receptacle inside the unit.
5. Attach the ground wire of the Quick Connect Cord to the terminal block fixing plate.
(If the ground wire is not attached, electrical noise may cause problems).
6. Secure the Quick Connect Cord with a clamp.
7. Replace the front cover.

Caution

For Quick Connect Multi System Installation use part No.CF-0706891 only. (sold separately).

Quick Connect
Cord

"Quick Connect Cord" tag

A

B

1.Red
2.Black
3.White
4.Green
5.Blue
6.Blue

1.Red
2.Black
3.White
4.Green
5.Blue
6.Blue

1.Red
2.Black
3.White
4.Green
5.Blue
6.Blue

1.White
2.Green
3.Red
4.Black
5.Blue
6.Blue

The wire coloring on the Quick Connect Cord will
not be the same as the wire coloring of the
connection plug inside the unit.
* The remote controller can be connected to either

unit A or B. Do not connect a remote controller to
both units.

* Disconnect the remote controller from either unit

A or B prior to installing the Quick Connect Cord.

Connecting Quick Connect Cord

Wiring Throughway

Wiring Throughway

Coupling Cord

Coupling Cord

Clamp

Clamp

Ground wire Connector

(Use one of the vacant holes)

Ground wire Connector

Connector

Connector

TH32ECR6 series

TH28ENR6 series

Wiring Throughway

Coupling Cord

Clamp

Ground wire Connector

(Use one of the vacant holes)

Connector

TH50ECR6 series

32

«
...
30
31
32
33
34
...
»

Содержание TH28ENR6L





















































Отзывы:

Нет отзывов

Похожие инструкции для TH28ENR6L

SmartWater GXSF18G

Бренд: GE Страницы: 2

Бренд: GE Страницы: 8

Бренд: GE Страницы: 28

Бренд: GE Страницы: 28

SmartWater GXSF27B

Бренд: GE Страницы: 80

Бренд: GE Страницы: 72

Бренд: GE Страницы: 60

Бренд: GE Страницы: 20

Бренд: GE Страницы: 20

Бренд: Danfoss Страницы: 72

Бренд: Danfoss Страницы: 91

Бренд: JABSCO Страницы: 4

Бренд: ACESOL Страницы: 36

Бренд: CASO DESIGN Страницы: 139

Бренд: Primo Water Страницы: 12

Бренд: Waterax Страницы: 6

SCP 16000 IQ Level Sensor

Бренд: Kärcher Страницы: 76

Бренд: QualityCraft Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды