Thermann TH28ENR6L Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 52

background image

Before installing, check for the following:

The location of the flue terminal must comply with the clearances shown on this page. If you are
unsure about clearances not indicated here, in general refer to AS/NZS5601, or your local authority.
In Western Australia refer to the WA Office of Energy rules and regulations.
Flue outlet must be free from any combustible material.

The continuous flow water heaters are certified for side by side installation and hence the flue terminal

clearance between the units mentioned in AS/NZS 5601.1 does not apply.
SAI Global certification allows minimum clearance of 268mm (exhaust to inlet of adjacent unit) for 28L

outdoor units.
SAI Global certification allows to install with the minimum distance of 480mm(between the centerlines of

the flue terminal) for 50L outdoor units.

WARNING

• Install the water heater in a location where it is free from obstacles and

stagnant air.

• Consult with the customer concerning the location of installation.
• Do not install the water heater near staircases or emergency exits.
• Do not install the water heater where the exhaust will blow on outer walls

or material not resistant to heat. Also consider the surrounding trees and
animals.

The heat and moisture from the water heater may cause discoloration of
walls and resinous materials, or corrosion of aluminium materials.

• Do not locate the flue termination directed towards a window or any other

structure which has glass or wired glass facing the termination.

• Install in a location where the exhaust gas flow will not be affected by fans

or range hoods.

• Take care that noise and exhaust gas will not affect neighbours.
• Avoid installation where the unit will be exposed to excessive winds.
• Before installing, make sure that the flue termination will have the proper

clearances according to AS/NZS5601, or your local authority.

• On combustible surfaces e.g. weatherboards etc. it is not required to install

a fire proof back board.

CAUTION

Prohibited

Installation Clearances

17

«
...
15
16
17
18
19
...
»

Содержание TH28ENR6L





















































Отзывы:

Нет отзывов

Похожие инструкции для TH28ENR6L

Бренд: Pakole Страницы: 35

Бренд: Warner Instruments Страницы: 3

Бренд: Warmlite Страницы: 8

Бренд: Phillips & Temro industries Страницы: 3

Бренд: T.I.P. Страницы: 136

Бренд: Rinnai Страницы: 31

Бренд: HOMCOM Страницы: 23

FastHeat Digital 14160

Бренд: Kerbl Страницы: 32

Бренд: Orbegozo Страницы: 91

Бренд: Stihl Страницы: 164

Бренд: Warmtech Страницы: 21

Бренд: B. Braun Страницы: 20

Бренд: Burcam Страницы: 10

Бренд: D-D The Aquarium Solution Страницы: 18

Бренд: SAMUEL JACKSON Страницы: 64

Бренд: Hubbell Страницы: 27

Бренд: Reliable Страницы: 18

Edel Wasser PWC-670-ORANGE

Бренд: Zepter Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды