Thermann TH28ENR6L Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 52

background image

Thermann Installer's Manual
Gas Continuous Flow Water Heaters

To be installed and serviced only by an authorised person.

This appliance is not suitable for use as a pool heater.

The "authorised installing person" is responsible for:
1. Correct commissioning of this appliance
2. Ensure unit performs to the specification stated on the data label
3. Demonstrate operation of unit to customer before leaving
4. Hand these instructions to customer

This appliance must be installed in accordance with the manufacturer's installation instructions all Local
Building, Water and Gas fitting regulations (AS/NZS3500.4, AS/NZS 5601, AS/NZS3000).

This appliance delivers water in excess of 50 Degrees C. Ensure that suitable devices such as Tempering
Valves are installed in lines servicing Sanitation areas per AS3500.4.

Failure to install this appliance in accordance with these installation instructions may void
warranty.

In the interest of continued product improvement, Reece Manufacturing reserves the right to alter these
specifications without notice.

2

«
1
2
3
4
...
»

Содержание TH28ENR6L





















































Отзывы:

Нет отзывов

Похожие инструкции для TH28ENR6L

Бренд: Nectre Fireplaces Страницы: 17

Бренд: WaterBoss Страницы: 36

Бренд: SAHP Страницы: 41

Бренд: JEC Страницы: 13

Бренд: SAER Elettropompe Страницы: 36

Бренд: ICON Страницы: 16

Instant-Flow Micro M-15L/277

Бренд: Chronomite Страницы: 2

Бренд: ProMinent Страницы: 77

KLIMATRONIC HEAT SUPREME

Бренд: Suntec Wellness Страницы: 124

Бренд: Cocoon Concept Страницы: 5

Comfort SC-FH53015

Бренд: Scarlett Страницы: 8

Бренд: Masterbuilt Страницы: 4

Бренд: REMKO Страницы: 16

Бренд: Somogyi Elektronic Страницы: 20

Бренд: FUXTEC Страницы: 4

Бренд: Laars Страницы: 64

Бренд: Comfort Flame Страницы: 28

Бренд: Rinnai Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды