Thermal Dynamics DRAG-GUN 38 Скачать руководство пользователя страница 45

Страница: 45 / 60

Manual 0-2729

SECTION 5: SERVICE

4. Remove the three nuts and star washers securing

the Capacitor PC Board to the Main PC Board As-
sembly. The nuts are located at terminals (+), (-),
and (N). Remove the Capacitor PC Board from unit.

5. Install the replacement Capacitor PC Board by re-

versing steps 1-3. Torque the three nuts on termi-
nals (+), (-), and (N) to 15 inch-lbs (1.695 mm).

CAUTION

DO NOT overtorque the nuts on the terminals as
the PC Board may be damaged.

n. Pilot Resistor (R1) Replacement Procedure

1. Remove the right panel per paragraph 'D' above.

2. Locate the Pilot Resistor near the outside edge of the

unit, below the Main PC Board Assembly.

NOTE

There are two resistors mounted to this area, Pilot
Resistor (R1) (15 ohms) and Damping Resistor (30
ohms). The Pilot Resistor is mounted on the bot-
tom.

Pilot Resistor

(R1)

Damping Resistor

A-02143

Figure 5-21 Pilot Resistor (R1) Replacement

3. Using a phillips screwdriver, remove the two screws

securing the Pilot and Damping Resistors to the
internal frame.

4. Pull the Pilot Resistor out far enough to gain access

to the two wiring connections.

5. Remove the two wires connected to the Pilot Resis-

tor noting the location of each.

6. Install the replacement Pilot Resistor by reversing

steps 1-5.

o. Pilot Resistor (R3) Replacement Procedure

1. Remove the right panel cover per paragraph 'D'

above.

2. Remove the two screws securing the center divider

to the unit base. Lift the vertical center divider up
and out towards the Compressor to gain access to
the Resistor.

3. Locate Resistor (R3), as shown in the figure below.

4. Note wiring locations, then remove the red and blue

wires from the terminals on Resistor R3.

5. Remove Resistor.

6. Install replacement Resistor, by reversing the above

steps.

A-02128

Resistor R3

Figure 5-22 Pilot Resistor (R3) Replacement

Содержание DRAG-GUN 38





























































Результаты поиска

Содержание DRAG-GUN 38

Отзывы:

Бренды по названию

Популярные бренды

Thermal Dynamics DRAG-GUN 38, Инструкция по эксплуатации

Результаты поиска

Содержание DRAG-GUN 38

Отзывы:

Бренды по названию

Популярные бренды