manualshive.com logo in svg

Thermal Dynamics DRAG-GUN 38, Инструкция по эксплуатации

Поделиться
Скачать
Thermal Dynamics DRAG-GUN 38 Скачать руководство пользователя страница 41

Manual 0-2729

35

SECTION 5: SERVICE

5.11  Power Supply Component

Replacement Procedures

NOTES

Refer to Section 6, Parts Lists, for replacement parts
and ordering information.

Refer to Exploded View for replacement parts and
parts orientation.

WARNING

Disconnect primary power to the system before dis-
assembling the torch, leads, or power supply.

A.  Handle Replacement

1.  Remove four screws attaching the handle to the rear

panel of the Power Supply.

2.  Install replacement handle.

B.  Filter Dryer Element Replacement

1.  Locate the Filter Dryer on the exterior of the Rear

Panel of the Power Supply.

2.  Remove Filter Dryer metal bowl by turning the bowl

counter-clockwise .

3.  Remove  Element Assembly from plastic bell by turn-

ing counter-clockwise.

4.  Disassemble  Element Assembly, as shown in Fig-

ure 5-14,  and remove Element.

5.  Install replacement Element by reversing above steps.

A-02136

Plastic Bell

Filter Dryer

Element

Figure 5-14  Filter Dryer Assembly

C.  Current Control Knob Replacement

1.  Using a small blade screwdriver, loosen the screw

securing the knob to the CURRENT Control adjust-
ment shaft.

2.  Turn the CURRENT Control adjustment shaft fully

clockwise.  This will represent the maximum posi-
tion.

3.  Slide the replacement knob onto the shaft.

4.  Turn the knob so that the line on the knob points

towards the wide end of the current control sym-
bol.

5.  Tighten the screw in the knob to secure the knob to

the shaft.

6.  Turn the knob fully counterclockwise.

7.  The line should now line up with beginning of the

CURRENT Control adjustment symbol.

8.  Adjust the knob as required to align the minimum

and maximum reference points.

D.  Side Panel Cover Removal  (Left or Right)

1.  Remove the six screws securing side panel to unit.

2.  Remove side panel from Power Supply, being care-

ful not to strain ground wire connection to panel.

3.  Rest cover beside Power Supply.

NOTE

To replace panel, disconnect ground wire.  Connect
ground wire to replacement panel and reverse above
steps.

Содержание DRAG-GUN 38





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды