4
Parameter
Description
Can be
queried
SendoPro
868-A
Can be
changed
SendoPro
868-A
Can be
changed
theSenda
P
Time delay
Channel A light
Value ranges
in seconds /
minutes
x
x
Pulse
x
x
Short presence
Channel A light
On / Off
x
Configuration
type
auto / man
x
x
x
Control input S
Auto / switch /
push button S /
push button O
x
Detection sen
-
sitivity (PIR)
Value range in
increments
x
x
Group address
All / I / II / III
x
LED display
motion
Off / On
x
The parameters are sent to the presence detector with the
„SendoPro 868-A“ management remote control or with „the
-
Senda P“ installation remote control via infra-red. Changed
parameters are immediately applied and used by the detector.
With the „SendoPro 868-A“ management remote control,
parameters can be queried by sending values level-by-level
to the detector. If the sent values are below the set parame-
ter, the LED illuminates briefly. If the sent values are equal or
above the set parameter, the LED flickers for 2 seconds.
Control commands via remote control
Control command
Description
Can be
triggered
SendoPro
868-A
Can be
triggered
theSenda
P
Teach-in Channel
A light
The currently measured
brightness value is accepted
as the brightness switching
value. Values outside the
permitted range will automati-
cally be set to the appropriate
limit value.
x
x
Switch light on/off Lighting group can be swit
-
ched on and off.
x
x
Presence test
On / Off
x
x
Restart
Restart detector
x
x
Factory settings
Set all parameters and set
-
tings to factory setting.
x
Brightness switching value Channel A light
The brightness switching value defines the minimum desired
brightness. The current prevailing brightness is measured
below the presence detector. If the prevailing brightness
is below the switching value, the light switches on when a
presence is detected (in configuration type fully automatic
device).
Value range
Lux values with "SendoPro 868-A" management remote
control
The "theSenda P" installation remote control offers the
following values
(The currently measured brightness value (lux) can
be adopted with the "SendoPro 868-A" management
remote control, with the teach-in control command or
with the "theSenda P" installation remote control via the
teach-in button.)
Values outside the permitted range will automatically be
set to the appropriate limit value.
30 - 3000 lux
300, 500,
800 lux
- Deactivating the brightness measurement (the bright
-
ness has no influence)
- The light channels only switch after presence/absence.
Possible with "SendoPro 868-A" management remote
control or "theSenda P" installation remote control.
Measurement
off
Button
Time delay Channel A light
Value range
Adjustable values with "SendoPro 868-A" manage
-
ment remote control
In the "theSenda P" installation remote control, the
following values are available
10 s - 60 min
10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
60 min
Control for staircase light timer switch (0.5 s "on"
/ 10 s "off")
"SendoPro 868-A"
"theSenda P"
Pulse
Button
1
Short-term presence
The time delay of Channel A light can be switched off sooner
if a room is occupied only for a short time. (In fully automatic
and semi-automatic function modes)
The time delay is used according to set parameter.
Off
If someone enters an unoccupied room and it is only occupied for
up to 30 seconds, the light goes off 2 minutes early.
On
Configuration type
Fully automatic device: The lighting switches on and off automati
-
cally. (due to presence/no presence and brightness)
auto
Semi-automatic: Switch on must always occur manually. Switch off
occurs automatically by the presence detector. (due to presence or
brightness)
man
Control input S
Control input S for manual switch on/off of Channel A light
automatically detects push buttons or switches.
Several push buttons can be connected to control input S
Use light push button only with neutral conductor connector
