11
LED lamps
< 2 W
2 – 8 W
> 8 W
60 W
180 W
200 W
Guidance value max. inrush current level
800 A / 200 µs
Maximum number EBs T5/T8
16 x 54/58 W, 24 x 35/36 W
8 x 2 x 54/58 W
12 x 2 x 35/36 W
Channel H, presence
Relay, floating, base insulation
Maximum voltage
220 V DC / 250 V AC
Maximum switching capacity
50 W / 50 VA (max. 2 A)
Recommended minimum load
10 mV / 10 mA
Connection type
Screw terminals
Max. cable cross-section
max. 2 x 2.5 mm²
Size of flush-mounted box
Size 1, Ø 55 mm (NIS, PMI)
Protection rating
IP 20 (IP 40 installed)
Ambient temperature
0 °C – 50 °C
CE Declaration of Conformity
This device conforms to the
safety regulations of the EMC
directive 20
1
4/
30
/E
U
and of
NSR 20
14
/
3
5/E
U
.
Product overview
Type of
installation
Channel
Operating
voltage
Colour
Type
Item
number
Ceiling
installation
Light |
HVAC
230 V AC
White
thePrema
P360 -101 E
2070105
Ceiling
installation
Light |
HVAC
230 V AC
Grey
thePrema
P360 -101 E
2070106
Ceiling
installation
Light |
HVAC
230 V AC
Special colour
in accor-
dance with
customer
information
thePrema
P360 -101 E
2070108
Troubleshooting
Fault
Cause
Light does not switch
on and/or off if pre-
sence is detected and
in darkness
Lux value is set too low; detector set on semi-au-
tomatic; light was switched off manually via push
button or theSenda S; person not within detection
area; obstruction(s) interrupting detection; time
delay set too short
Light stays on with
detection of presence
despite sufficient
brightness
Lux value is set too high; light was briefly switched
on manually via push button or with theSenda S
(wait 30 min.); detector is in test mode
Light does not switch
off and/or light swit-
ches on spontaneously
when no one is present
Wait for time delay (self-learning);
thermal sources of interference in the detection
area: fan heaters, incandescent lamps/halogen
spotlights, moving objects (e.g. curtains hanging in
an open windows);
Load (EBs, relays) not cleared
Push button does not
function
Device still in the start-up phase; illuminated push
button was used without neutral conductor;
Push button not led to the master
Light cannot be swit-
ched off with the push
button
DIP switch to "corridor" position; push button
not fed to the detector. Check wiring to the push
button
Device does not
respond
Short circuit or several phases in parallel switching!
Disconnect detector from the power supply for 5
mins. (thermal fuse)
Error flashing
(4 x per second)
Error in self-test;
Device not properly functional!
Guarantee
ThebenHTS presence detectors are manufactured with the
utmost care and using state-of-the-art technology and are
quality-tested. ThebenHTS AG therefore guarantees perfect
operation when used correctly. Should a fault occur, however,
ThebenHTS AG will fulfil the guarantee within the scope of the
general terms and conditions.
Please note in particular:
•
that the guarantee period lasts 24 months from the date
of manufacture.
•
that the guarantee is invalidated if you, or a third party,
make changes or undertake repairs to the devices.
•
that, insofar as the presence detectors are connected
to a software-controlled system, the guarantee for this
connection is only valid when the indicated interface
specification is complied with.
We undertake to repair or replace as quickly as possible
all components of the delivered device that have become
defective or unusable through demonstrably poor material,
faulty construction or incomplete delivery up to the end of the
guarantee period.
Returns
In the event of a guarantee claim, please return the device to
the relevant dealer together with the delivery note and a brief
description of the fault.
Industrial property rights
The design as well as hardware and software of these devices
are protected by copyright.
Dimensional diagrams
Flush-mounting
