Thaler KE-SP 3050 Скачать руководство пользователя страница 26

Страница: 26 / 28

In-Line filter

CS-050-P10-A

AFTER FIRST 50 HOURS, THEN @ 1000
HOUR INTERVALS

Breather (fill cap)

Wash out with solvent as required

Tank Capacity

16 Gallons

GREASE SCHEDULE

Red marked zerks

Multi-purpose EP-2

50 HOURS

Cross grooved
spindle

Multi-purpose EP-2

50 HOURS Clean with solvent

Drive chains

30W oil

50 HOURS Clean with solvent

Chain Tension

1/8 to 1/4 inch sag

50 HOURS See section 4.5 under
maintenance

WIRE ROPE

WIRE ROPE

.472 (12mm)
diameter

SSELSZSPAZNK1960 See section 4.4 under maintenance

TRAILER

Tire size

215/75R 17.5

Tire pressure

See Manual

Wheel Torque

See Manual

DOT Inspections

State & Federal

YEARLY PER REGULATIONS

Page 21

Troubleshooting Guide

Refer to the electrical and hydraulic schematics.

The toggle switch on the remote contro

l lever must always be in the “ON” position while pulling in

or paying out.

If the Emergency-Stop is pressed (or if the limited value of the measuring system

– pulling force

and length

– are exceeded and the winching operation is stopped), the remote winch lever must

be set back to center or zero position to allow a restart of the winching operation.

If problems occur with the KPR 2000 control system, refer to that system manual.

5.1

Diesel Engine

Refer to separate Owner’s Manual from Yanmar.

5.2

Trailer Electric Brake System

Refer

to separate Trailer Owner’s Manual from AL-KO.

Содержание KE-SP 3050





























Результаты поиска

Содержание KE-SP 3050

Отзывы:

Похожие инструкции для KE-SP 3050

Бренды по названию

Популярные бренды

Thaler KE-SP 3050, Руководство по эксплуатации

Результаты поиска

Содержание KE-SP 3050

Отзывы:

Похожие инструкции для KE-SP 3050

Бренды по названию

Популярные бренды