TGM MWVT09S Скачать руководство пользователя страница 45

Страница: 45 / 48

Service manual

- 44 -

10.2.2 E1(indoor / outdoor units communication protection) error diagnosis and solution

10.2.3 E2(zero-crossing signal error) diagnosis and solution

Disconnect the power supply, after 1 minute,

connect the power supply, turn on the unit with
remote controller

Does the unit work normally?

Check the wiring between
indoor and outdoor unit. Is
the connection of L, N, S and
GND good?
Is the GND connection on
outdoor PCB good?

Reconnect and retest again

Is the LED4 (red) on
outdoor PCB bright and
LED1(yellow) blinking?

Replace outdoor e-box.

Yes

The power supply for
outdoor PCB is fail. Check
the wiring on outdoor PCB
comparing with wiring plate.
Is the connection good?

Correct the connection.

Yes

Replace indoor PCB
and repower on. Is
the failure cleared?

Is power supply and
connection of connectors
good?

Indoor PCB is defective. Replace
the indoor PCB.

Be sure the power supply is good
and correct the connection

YES

Содержание MWVT09S

















































Результаты поиска

Содержание MWVT09S

Отзывы:

Похожие инструкции для MWVT09S

Бренды по названию

Популярные бренды

TGM MWVT09S, Руководство по обслуживанию

Результаты поиска

Содержание MWVT09S

Отзывы:

Похожие инструкции для MWVT09S

Бренды по названию

Популярные бренды