10
IV.
MACHINE SET UP (Cont’d)
4)
Adjust the endseal opening crank (labeled B) so that the bottom pad of the endseal is slightly
below the surface of the conveyor, the product should also clear under the top bar of the endseal.
5)
Adjust the film inverting head to product height using the crank on top of the infeed conveyor.
6)
Endseal closure operation will vary with adjustments in endseal opening. With each new product
height setup, adjustments of the flow controls will be necessary to prevent machine “banging”.
Two flow control valves are located together on the main air cylinder, one adjusts the opening
speed of the endseal, and the other adjusts the closing speed of the endseal. Adjust these while
the machine is running, or use the manual seal button on the keypad, until a smooth and quite
operation of the endseal results. The main air cylinder is located beneath the endseal system.
7)
The main air regulator should never exceed 80 PSI. The recommended PSI is 75. Exceeding 80
PSI will damage internal mechanisms.
8)
“Dry Run” the product without film and check for proper product spacing. In general, the
distance between products, on the middle conveyor, should be 1.5 times the product height.
Tune conveyor speeds and mechanical adjustments. The “Test Mode” can be used to help
establish machine speed. Refer to the “Test Mode” section for a more detailed description.
9)
Adjust the sealing position of the cross-seal between packages with end seal lag. Increasing
endseal lag moves cross-seal further from trailing edge of lead package.
10)
When satisfied with machine performance, load film (see Section B below).
11)
Use the infeed jog key to convey product into the first conveyor from an auxiliary conveyor if
utilized.
12)
Press the green automatic on/off button to start operation.
13)
Remember to catch scrap bag in front of first product.
14)
Any adjustments can be made while the machine is running, both mechanical and touch screen
values.
Содержание 2200SS SIDE SEAL
