Textron Ransomes Mastiff 91 Series Скачать руководство пользователя

Страница: 41 / 100

SAFETY, OPERATORS & MAINTENANCE MANUAL

GB-41

ADJUSTMENTS

9.13 TESTING GEAR SELECTION

Perform the following tests to determine the correct
function of the gear selection mechanism; do not use
the machine until any failures have been rectified

Select forward drive using the gear lever,

check the gear lever is still free to move and
does not catch in the gate.

Select reverse gear using the gear lever. It

should be possible to do this without using
excess force and without the lever catching the
gate.

Gently tap the gear lever out of reverse until the

lever just drops into neutral, check the landroll
drive cog is free to rotate and the machine is in
neutral.

NOTE: It is important not to pass the neutral position
when performing this test as this can give false
results.

9.14 ADJUSTING GEAR SELECTION

MECHANISMS

Remove the chain cover and tensioner retain-
ing plate before inserting the locking pin as
shown on both tensioners.

Remove both the chains noting the orientation

of the king links before removal

Remove the gearbox cover

Slacken the locknut on both gear levers.

Remove the locating pins noting the loction of
any washers before removal.

Engage the cutting cylinder and forward

drive by pushing the bellcranks forward.

Move the gear lever to forward in the gate

NOTE: The clutch spider has been removed for photograph.

Содержание Ransomes Mastiff 91 Series





































































































Результаты поиска

Содержание Ransomes Mastiff 91 Series

Отзывы:

Похожие инструкции для Ransomes Mastiff 91 Series

Бренды по названию

Популярные бренды

Textron Ransomes Mastiff 91 Series, Инструкция по безопасности, эксплуатации и техническому обслуживанию/Список запасных частей

Результаты поиска

Содержание Ransomes Mastiff 91 Series

Отзывы:

Похожие инструкции для Ransomes Mastiff 91 Series

Бренды по названию

Популярные бренды