Texas Snowbuster 1100E Скачать руководство пользователя страница 22

Страница: 22 / 22

TROUBLESHOOTING

WARNING

Turn off the engine and pull out the ignition cable before

making any inspection or adjustments.

If after making an adjustment or repair to the engine, and

you let it run for a few minutes, remember that the

exhaust and other parts will get hot.

Do not touch these parts as these may burn you.

Fault

Possible causes

Remedy

The unit does not operate

smoothly and vibrates

intensively

Bolts loose

Auger unit mounting loose

Check bolts

Check auger unit mounting

Engine does not run

Throttle lever in wrong

position

Spark plug defective

Fuel tank empty

Fuel cock closed

Check setting

Replace spark plug

Top up fuel

Open fuel cock

Engine does not run smoothly

Bad Fuel

Spark plug dirty

Empty Fuel Tank and refill with

Fresh Fuel

Clean the spark plug

Drive power falls

Clutch play too large

Drive Belt loose or

damaged

Adjust clutch cable

Replace Drive Belt

Contact authorized customer

service

The engine will not start or dies

after a short period of time

Choke in wrong position

Spark plug Fouled

No fuel

Check Choke setting

Clean or replace spark plug

(electrode spacing 0.6mm)

Top up fuel

Inadequate or no ejection

Snow ejection until

blocked

Plow screw not turning

Shearing bolts sheared

Clean the snow ejection unit with a

solid object

Adjust Auger clutch cable

Replace shear bolts or contact

authorized customer service

The snow is not removed fully

Skids maladjusted

Adjust the skids

Содержание Snowbuster 1100E























Результаты поиска

Содержание Snowbuster 1100E

Отзывы:

Похожие инструкции для Snowbuster 1100E

Бренды по названию

Популярные бренды

Texas Snowbuster 1100E, Руководство пользователя

Результаты поиска

Содержание Snowbuster 1100E

Отзывы:

Похожие инструкции для Snowbuster 1100E

Бренды по названию

Популярные бренды