Texas Instruments TLV320AIC3109EVM-K Скачать руководство пользователя страница 6

Страница: 6 / 67

EVM Description and Basics

www.ti.com

SLAU738 – September 2017

TLV320AIC3109EVM-K

EVM Description and Basics

This section provides information on the analog input and output, digital control, power and general
connection of the TLV320AIC3109EVM-K.

2.1

Default Configuration and Connections

2.1.1

TLV320AIC3109EVM Default Connections

Table 2

provides a list of jumpers found on the EVM and their factory default conditions.

Table 2. List of Jumpers

Jumper

Default

Position

Jumper Description

2-3

Mic bias selection: when connecting 2-3, mic bias comes from the MICBIAS pin
on the device; when connecting 1-2, mic bias is supplied from an external power
source connected to J6

Open

Connects onboard Mic to IN1P

J11

Open

When installed, shorts across the input AC coupling capacitor on IN2M, for DC
measuring purposes only

J12

Open

When installed, shorts across the input AC coupling capacitor on IN2P, for DC
measuring purposes only

J14

Open

When installed, shorts across the input AC coupling capacitor on IN1M, for DC
measuring purposes only

J15

Open

When installed, shorts across the input AC coupling capacitor on IN1P, for DC
measuring purposes only

J18

Open

When installed, shorts across the output capacitor on HPCOM; remove this
jumper if using AC-coupled output drive

J19

Open

When installed, shorts across the output capacitor on HPOUT; remove this
jumper if using AC-coupled output drive

J22

2-3

IOVDD selection: when connecting 2-3, IOVDD is set to +3.3 VD; when
connecting 1-2, IOVDD and DVDD are shorted at +1.8 VD

J23

Open

When installed, allows the USB-MODEVM to hardware reset the device under
user control

J24

Installed

Provides a measuring point for AVDD current

J25

Installed

Provides a measuring point for DRVDD current

J26

Installed

Provides a measuring point for DVDD current

J27

Installed

Provides a measuring point for IOVDD current

J28

Installed

Connects analog and digital grounds on the lower part the board

J29

Installed

Connects analog and digital grounds on the upper part the board

J30

Open

Selects onboard EEPROM as firmware source

Содержание TLV320AIC3109EVM-K




































































Результаты поиска

Содержание TLV320AIC3109EVM-K

Отзывы:

Похожие инструкции для TLV320AIC3109EVM-K

Бренды по названию

Популярные бренды

Texas Instruments TLV320AIC3109EVM-K, Руководство пользователя

Результаты поиска

Содержание TLV320AIC3109EVM-K

Отзывы:

Похожие инструкции для TLV320AIC3109EVM-K

Бренды по названию

Популярные бренды