Texas Instruments TLV320AIC3109EVM-K Скачать руководство пользователя страница 21

Страница: 21 / 67

www.ti.com

TLV320AIC3109EVM Software

SLAU738 – September 2017

Submit Documentation Feedback

TLV320AIC3109EVM-K

4.7

AGC Tab

The

AGC

tab consists a set of controls to configure the automatic Gain Control (AGC) of the

TLV320AIC3109-Q1. The AGC function is described in

TLV320AIC3109-Q1 Automotive, Low-Power, 96-

kHz, Mono Audio Codec

. The default

AGC

tab configuration is shown in

Figure 13

Figure 13. AGC Tab

The AGC can be enabled using the

Enable

button.

Target

gain (dB),

Attack

time (milliseconds),

Decay

time (milliseconds), and the

Maximum PGA Gain Allowed

(dB) can all be set, respectively, using the four

corresponding knobs.

The TLV320AIC3109-Q1 allows for the Attack and Decay times of the AGC to be set up in two different
modes, standard and advanced. The

AGC Settings

button determines the mode selection. The

Standard

mode provides several preset times that can be selected by adjustments made to the

Attack

and

Decay

knobs. If finer control over the times is required, then the

Advanced

mode should be selected. When the

Advanced

mode is enabled, two tabs should appear that allow separate, advanced control of the Attack

and Delay times of the AGC (see

Figure 14

). These options allow selection of the base time as well as a

multiplier to achieve the actual times shown in the corresponding text box. The

Use advanced

button

should be enabled to program the registers with the correct values selected via the pull-down options for
base time and multiplier.

Figure 14. Advanced AGC settings

Содержание TLV320AIC3109EVM-K




































































Результаты поиска

Содержание TLV320AIC3109EVM-K

Отзывы:

Похожие инструкции для TLV320AIC3109EVM-K

Бренды по названию

Популярные бренды

Texas Instruments TLV320AIC3109EVM-K, Руководство пользователя

Результаты поиска

Содержание TLV320AIC3109EVM-K

Отзывы:

Похожие инструкции для TLV320AIC3109EVM-K

Бренды по названию

Популярные бренды