PORTABLE HIGH-ENERGY IGNITER
– XE18PB06 - Rev.00
31
a water flood;
a powder extinguisher, by avoiding to address the jet on the victim face;
some blankets to be thrown on the victim or by rolling the victim itself on the ground.
2)
Don’t detach any fabrics’ tatters adhering at the skin.
3)
In case of burns caused by liquids, remove quickly but cautiously the wet garments
.
4)
Cover the burns
with a purposed surgical packet or by using a sterile bandage.
3.3.3.
CORROSION
The corrosion to the eyes is provoked both by the lubricating oil and by the water and cement powder mixture
.
Also batteries liquid or capacitors filling fluid could be corrosive.
Rinse the eye with water for at least 20 minutes, by keeping the eyelids open, in order to allow the water to
flow along the eye contour and by moving the eye in every direction, having then immediately recourse to the
medical aids.
3.3.4.
ELECTRIC SHOCK
The electrocution injuries may be caused by:
external electric wirings;
electric equipments.
In both cases, the voltage value causes the passage of high currents through the human body.
In case of a short circuit provoked, for example, by a metal tool, some sparkling could arise, causing burns.
In those cases, try by every mean to cut out the current before touching the victim.
Shouldn’t this be possible, remember that any other attempt is highly dangerous also for the rescuer;
consequently, the rescue attempt must be performed by using fully insulated tools.
3.3.5.
WOUNDS AND FRACTURES
The vastness of the possible cases and the specificity of the interventions necessarily requires the
intervention of the medical structures.
In case of bleeding, press the wound from the outside, up to the rescuers arrival.
In case of a fracture, don’t move the part of the body concerned by the fracture itself, and, only if absolutely
necessary, displace the victim with the utmost care.
3.3.6.
ELASTOMERIC MATERIAL
The elastomeric materials which were subjected to temperatures higher than 300° C must be handled by
observing the following procedure. Wear heavy rubber gloves and special protective glasses.
1)
Remove the material and put it into plastic bags
.
2)
Wash the polluted area by using an alkaline solution.
Содержание XE18PB06
