background image

 

 

 

 

 

28 

PORTABLE HIGH-ENERGY IGNITER 

– XE18PB06 - Rev.00 

3.1 SAFETY GENERAL PRINCIPLES 

As  far  as  it  was  possible, 

TESI  s.r.l.

  has  made  every  effort  in  designing  the  High  Energy  Igniter,  making  it 

inherently safe. 
The device is equipped with protections and safety devices deemed necessary and, finally, is accompanied by 
sufficient information for its safe and properly utilization. 
 
If the device is used in compliance with the terms of use, following the use instruction and is subject to regular 
maintenance,  it  can  operate  safely;  on  the  contrary,  the  inobservance  of  the  use  and  maintenance  rules, 
makes the High Energy Igniter dangerous both for the operator and for other people. 
 

  

WARNING 
Before  using  the  High  Energy  Igniter,  carefully  read  the  instructions  supplied  in  this 
manual and follow the here reported indications. 
It is also mandatory that the operator complies the safety rules and instructions related to 
the worksite in which it operates 

 
If a warning message can’t be fully understood, ask 

TESI s.r.l.

 for the relevant explanations. 

 
For  safety  purposes,  it  is  anyway  not  sufficient  to  carefully  observe  the  safety  warnings;  for  the  whole 
utilization  time  of  the  High  Energy  Igniter,  it  is  necessary  to  foresee  all  the  possible  dangers  and  to  make 
every effort in order to prevent them. 
 
Never  begin  any  work  without  having  before  determined  that  both  his  own  and  others 

people’  safety  are 

safeguarded. 
 
Never  undervalue  his  own  doubts,  and,  if  any  uncertainty  exists  about  the  High  Energy  Igniter  or  about  the 
work to be performed, get addressed to somebody competent. 
 
Should any anomalous situations be noticed, it is obligatory to immediately stop the High Energy Igniter and to 
urgently inform either the foreman or the competent body about the event. 
 
Always act with: 
 

PRUDENCE - ATTENTION - PRECAUTION 

 

 
 
 
 
 
 
 
 
 
 
 

  

CAUTION 
For any further concern or required explanation, please contact TESI s.r.l. 

  

Содержание XE18PB06



































































Отзывы: