Terra Universal USP 797 Скачать руководство пользователя страница 20

Страница: 20 / 42

Quick-Start Operating Guide

USP 797 Modular Cleanroom

Terra Universal, Inc. • TerraUniversal.com • 800 S. Raymond Ave. • Fullerton, CA 92831 • TEL: (714) 578-6000 • FAX: (714) 578-6020

NOTE

If your cleanroom requires seismic anchoring, be sure to adhere to local seismic codes.

For example:

Prior to installing wall panels, drill and install an anchor every 4’ along the base frame about 2” from the vertical frame, and one

into the base of the door frame underneath the control panel. The holes should be drilled into the base frame approximately 2”

away from the vertical frame posts. Avoid drilling through the corner inserts or through the connector pieces; drill only through

the H-frames. For the top face of the base frame, drill a 5/8” hole to fit the anchor. Directly beneath it, drill a ½” hole. The concrete

should be a minimum of 6” deep and field verified. Use 3/8” Kwik Bolt TZ (not included) for a minimum embedment of 3-5/8”.

The diagram below is an example, local seismic codes may vary.

Содержание USP 797











































Результаты поиска

Содержание USP 797

Отзывы:

Похожие инструкции для USP 797

Бренды по названию

Популярные бренды

Terra Universal USP 797, Быстрый старт Руководство по эксплуатации

Результаты поиска

Содержание USP 797

Отзывы:

Похожие инструкции для USP 797

Бренды по названию

Популярные бренды