Terra Universal USP 797 Скачать руководство пользователя страница 32

Страница: 32 / 42

Quick-Start Operating Guide

USP 797 Modular Cleanroom

Terra Universal, Inc. • TerraUniversal.com • 800 S. Raymond Ave. • Fullerton, CA 92831 • TEL: (714) 578-6000 • FAX: (714) 578-6020

Installing Top Corners, Operation Status Indicators, and Side Trim Fascia

Begin by positioning the corner trim with Operation Status Indicator (TUI Logo) on the top corner posts so that all

holes are aligned. The corner trim should fall over the wallboard installed earlier. Loosely fasten #6 x 1-5/8”

Bugle-Head self-tapping drywall screws through the wallboard and into the steel frame.

Install the top fascia trim strips next to the corner trim. Each piece attaches to the adjacent piece by means of

two screw holes on the mounting plates, which bend 90 degrees inward. For each connection, use one 8/32

Phillips screw, two flat washers, one lock washers and one acorn nut. Do not tighten.

Ceiling Panel Caulking

To meet USP 797 requirements for a sterile environment, seams along the edges of the cleanroom ceiling panels

must typically be caulked. Terra provides 100% silicone sealant for this purpose. Prior to caulking, carefully clean all

panel-to-frame seams with a clean, non-woven wiper saturated with appropriate cleaning agent (such as 70% IPA /

30% DI water). Allow cleaned surfaces to dry before applying sealant with a caulking gun (not provided). Apply a

Installing the top trim fascia:

use #6 x 1-5/8” Bugle-

Head self-tapping drywall screws to attach pieces to

frame (using pre-drilled holes) and 8/32 screws with

washers and acorn nuts to connect adjoining pieces.

Operation Status Indicator lights

connect to the PDM

by means of low-voltage telephone cable. When

connected, they should glow continuously as long as

FFUs are ON, and flash intermittently when they are

turned OFF.

Содержание USP 797











































Результаты поиска

Содержание USP 797

Отзывы:

Бренды по названию

Популярные бренды

Terra Universal USP 797, Быстрый старт Руководство по эксплуатации

Результаты поиска

Содержание USP 797

Отзывы:

Бренды по названию

Популярные бренды