Terasic HDMI-FMC Скачать руководство пользователя страница 20

Страница: 20 / 46

- 19 -

HDMI-FMC_User_Manual

www.terasic.com

August 6, 2019

information).

The register sets for both modes overlap, so only one can be accessed at a time. However, by toggling

between the two groups, features from both can be intermixed.

The registers available at TPI 0x62–0x6D depend on the setting of TPI 0x60[7].

⚫

Setting TPI 0x60[7] = 0 selects external sync and access to the DE Generator registers. The DE

signal can be generated internally and sent over TMDS if TPI 0x62–0x6D are set and then TPI

0x63[6] is set to 1.

⚫

Setting TPI 0x60[7] = 1 allows access to the Embedded Sync Extraction registers. The DE,

HSYNC, and VSYNC signals can then be extracted and sent over TMDS if TPI 0x62–0x69 are

set and then TPI 0x63[6] is set to 1.

Features from both groups can be enabled together, by enabling the features of each group with TPI

0x60[7] set appropriately.

Access.

These registers are accessed as single bytes or as part of a burst.

Table 3-6 Sync Register Configuration and Sync Monitoring Registers

Offset

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0x60

[04]

Sync Generation Control Register

Sync Method

0 – External

1 –

Embedded

RSVD

YC Mux

Mode

One- to

two-data-ch

annel

de-mux

0 – Disable

1 – Enable

Invert Field

Polarity

0 – Leave

bit as is

1 – Invert

field bit

RSVD

DE_ADJ#

0 – Enable

(recommended

)

1 – Disable

(default)

F2VADJ

Adjust VBIT

to VSYNC

per bit [0]

0 – Disable

(default)

1 – Enable

F2VOFST

Adjust VBIT

to VSYNC if

bit [1] = 1

0-Decrement

by 1

1 –Increment

by 1

0x61

[00]

Video Sync Polarity Detection Register (RO)

RSVD

RSVD RSVD

RSVD

Interlace Mode

detected

0 – non

interlaced

1 – interlaced

Input VSYNC

polarity detected

0 – active

high (leading

edge rises)

Input HSYNC

polarity

detected

0 – active high

(leading edge

Содержание HDMI-FMC















































Результаты поиска

Содержание HDMI-FMC

Отзывы:

Похожие инструкции для HDMI-FMC

Бренды по названию

Популярные бренды

Terasic HDMI-FMC, Руководство пользователя

Результаты поиска

Содержание HDMI-FMC

Отзывы:

Похожие инструкции для HDMI-FMC

Бренды по названию

Популярные бренды