Tempco TEC-9300 Скачать руководство пользователя страница 3

Страница: 3 / 92

Warning Symbol

This symbol calls attention to an operating procedure, practice, or

the like which, if not correctly performed or adhered to, could

result in personal injury or damage to or destruction of part or all

of the product and system. Do not proceed beyond a warning sym-

bol until the indicated conditions are fully understood and met.

Using the Manual

Installers . . . . . . . . . . . . . . . . . . . . . . . . . . . Read Chapters 1, 2

Basic Function User . . . . . . . . . . . . . . . . Read Chapters 1, 3, 5

Enhanced Function User . . . . . . . . . . Read Chapters 1, 3, 4, 5

System Designer . . . . . . . . . . . . . . . . . . . . . Read All Chapters

Expert User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read Page 8

NOTE:

It is strongly recommended that a process should incorpo-

rate a LIMIT CONTROL like TEC-910 which will shut

down the equipment at a preset process condition in order to

preclude possible damage to products or system.

Information in this user’s manual is subject to change without

notice.

rights reserved. No part of this publication may be reproduced,

transmitted, transcribed or stored in a retrieval system, or trans-

lated into any language in any form by any means without the

written permission of Tempco Electric Heater Corporation.

ONTENTS

Page No

Chapter 1 - Overview

1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1-2 Hardware Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-3 Programming Port and DIP Switch . . . . . . . . . . . . . . . 3

1-4 Keys and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-5 Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-6 System Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1-7 Parameter Description . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 2 - Installation

2-1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2-2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2-3 Wiring Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2-4 Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2-5 Sensor Installation Guidelines . . . . . . . . . . . . . . . . . . . 16

2-6 Thermocouple Input Wiring . . . . . . . . . . . . . . . . . . . . 16

2-7 RTD Input Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2-8 Linear DC Input Wiring . . . . . . . . . . . . . . . . . . . . . . . 17

2-9 CT/Heater Current Input Wiring . . . . . . . . . . . . . . . . . 18

2-10 Event Input wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2-11 Output 1 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2-12 Output 2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2-13 Alarm 1 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2-14 Alarm 2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2-15 RS-485 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2-16 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2-17 Analog Retransmission . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 3 - Programming Basic Functions

3-1 Input 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3-2 OUT1 and OUT2 Types . . . . . . . . . . . . . . . . . . . . . . . 26

3-3 Configuring User Menu . . . . . . . . . . . . . . . . . . . . . . . . 26

3-4 Heat Only Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3-5 Cool Only Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3-6 Heat-Cool Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3-7 Dwell Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3-8 Process Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3-9 Deviation Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3-10 Deviation Band Alarms . . . . . . . . . . . . . . . . . . . . . . . 32

3-11 Heater Break Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3-12 Loop Break Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3-13 Sensor Break Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 34

3-14 SP1 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3-15 PV1 Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3-16 Failure Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3-17 Bumpless Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3-18 Self-tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3-19 Auto-tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3-20 Manual Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3-21 Signal Conditioner DC Power Supply . . . . . . . . . . . 39

3-22 Manual Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3-23 Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3-24 Heater Current Monitoring . . . . . . . . . . . . . . . . . . . . 40

3-25 Reload Default Values . . . . . . . . . . . . . . . . . . . . . . . . 40

ONTENTS

Page No

Chapter 4 - Full Function Programming

4-1 Event Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4-2 Second Set Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4-3 Second PID Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

4-4 Ramp and Dwell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

4-5 Remote Set Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4-6 Differential Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4-7 Output Power Limits . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4-8 Data Communication . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4-9 Analog Retransmission . . . . . . . . . . . . . . . . . . . . . . . . 45

4-10 Digital Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4-11 Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4-12 Pump Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4-13 Remote Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Chapter 5 - Applications

5-1 Pump/Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . 47

5-2 Variable Period Full Wave SSR (VPFW SSR) . . . . . . 47

5-3 Heat Only Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

5-4 Cool Only Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5-5 Heat-Cool Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5-6 Ramp and Dwell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

5-7 Remote Set Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5-8 Differential Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5-9 Dual Set Point/PID . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

5-10 RS-485 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

5-11 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

5-12 Retransmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Chapter 6 - Calibration

. . . . . . . . . . . . . . . . . . . . 55

Chapter 7 - Error Codes and

Troubleshooting

. . . . . . . . . . . . . . 57

Chapter 8 - Specifications

. . . . . . . . . . . . . . . . . 61

Chapter 9 - Modbus Communications

. . . 63

Appendix

A-1 Menu Existence Conditions . . . . . . . . . . . . . . . . . . . . 77

A-2 Factory Menu Description . . . . . . . . . . . . . . . . . . . . . 80

A-3 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

A-4 Memo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

A-5 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Содержание TEC-9300





























































































Результаты поиска

Содержание TEC-9300

Отзывы:

Tempco TEC-9300, Инструкция по эксплуатации, Страница: 3 / 92

Результаты поиска

Содержание TEC-9300

Отзывы: