manualshive.com logo in svg

Tempco TEC-9300, Инструкция по эксплуатации, Страница: 11 / 92

Поделиться
Скачать
Tempco TEC-9300 Скачать руководство пользователя страница 11

7

1–6 System Modes

The controller performs closed loop control in its normal control mode condition. The

controller will maintain its normal control mode when you are operating the user menu,

setup menu, display mode, reloading default values, or applying event input signals.

Under certain conditions, the normal control mode will transfer to an exception mode.

The  exception  modes  include:  sleep  mode,  manual  mode,  failure  mode,  calibration

mode, and auto-tuning mode. All of these modes perform in an open loop control except

auto-tuning mode which performs ON-OFF while configuring PID values control. The

mode transfer is governed by the priority conditions. A lower priority mode can not alter

a higher priority mode, as shown in figure 1.6.

System Modes

Sleep mode:

See section 4-11.

Manual mode:

See section 3-23.

Failure mode:

See section 3-17.

Calibration mode:

See chapter 6.

Auto-tuning mode:

See section 3-20.

Normal control mode:

See section 3-24, 3-26, 4-1

Calibration mode, auto-tuning mode, and normal control mode are in the

same priority level. Sleep mode is in the highest priority level.

Содержание TEC-9300





























































































Отзывы:

Нет отзывов