manualshive.com logo in svg

tellefsdal AUTO WRAP 1510, Руководство пользователя

Поделиться
Скачать
tellefsdal AUTO WRAP 1510 Скачать руководство пользователя страница 4

* Emergency stop: see chapter 2.1

4

2.0

SAFETY PRECAUTIONS.

TELLEFSDAL A.S does not take the responsibility for damages that may occur on machine,
persons or other equipment, because of the machine NOT being used as described in this
manual, or because of the safety precautions NOT being followed.

2.1

SAFETY EQUIPMENT.

Before using the machine, make sure that all guards and covers are securely fitted. The machine
must not be operated if a function does not work as described later in this manual. (See chapter 2.5).

The Auto Wrap 1510 / 1514 / TWIN models are equipped with an "EMERGENCY STOP" on the
wrapping arm. This device stops all functions instantly, but is by definition not an emergency
stop, because it does not interrupt the feed. Nevertheless it has an equivalent function, so we
have decided to call it an EMERGENCY STOP in this book.

2.2

BECOME FAMILIAR WITH THE OPERATIONS OF THE MACHINE.

If you are unsure how to operate the machine properly, either use of or maintenance to your Auto
Wrap, please contact your Auto Wrap dealer. 

 

2.3

ADJUSTMENTS' / MAINTENANCE.

Turn off the tractor and discharge the oil pressure before performing any adjustment or maintenance
on the machine. Remember that a well maintained machine is a safe machine. 

2.4

IMPORTANT!

MAKE ALWAYS SURE THAT NOBODY IS IN THE HAZARD

AREA OF THE WRAPPING ARM WHEN THE MACHINE IS IN USE.

THE MACHINE MUST NEVER BE OPERATED BY PERSONS WHOM DOES NOT KNOW ENOUGH

ABOUT HOW TO SAFELY OPERATE THE MACHINE, OR BY PERSONS UNDER 16 YEARS OF AGE.

Содержание AUTO WRAP 1510






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды