manualshive.com logo in svg

tellefsdal AUTO WRAP 1510, Руководство пользователя

Поделиться
Скачать
tellefsdal AUTO WRAP 1510 Скачать руководство пользователя страница 25

* Emergency stop: see chapter 2.1

25

Fig. 8-1

8.0

SPEED-SETTING OF THE WRAPPING ARM.

8.1

 Start the tractor, let it run  at approx. 1000 revolutions per min. lift the machin clear off  the ground.
The oil flow to the packing machine is adjusted with the use of two control valves which are placed
on the valve block situated behind the machines "neck".[see fig. 8-1]

8.2

The control valve on the right-hand side, is for adjustment of the wrapping arm speed. (See fig. 8-1).

8.3

Adjust the wrapping arm speed to approx. 22 revolutions per minute. (Just below three seconds per
revolution.) The adjustment is carried out by turning the wheel on the control valve. Turning

clockwise REDUCES

 the speed and turning 

counterclockwise INCREASES

 the speed.

It is recommended not to wrap with higher speed than 22 revolutions per minute, because then the
plastic film will "catch" more air, and this air do not reach to evacuate from the bale. The result is bad
fodder.

OBS! Max. allowed wrapping arm speed is 27 revolutions per minute.

REMEMBER!

Increased speed of tractor engine do not increase the wrapping speed, it only increases the
oil flow into the system and by that also the temperature in the hydraulic system.

Содержание AUTO WRAP 1510






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды