tell gsm easyaid Скачать руководство пользователя страница 12

 

12 

2.4.9  Voice call settings 

Incoming  calls  are  accepted  only  from  the  preconfigured  (up  to  4)  phone  numbers. 
Calls initiated from other phone numbers are rejected automatically. 
In  case  of  an  incoming  call  the  module  answers  the  call  automatically  in  hands-free 
mode after the configured number of rings. The call can be terminated by  pressing the 

Cancel 

  key,  or  by  the  caller.  The  call  is  also  terminated  if  an  emergency  call  is 

initiated. 
Due to the compact design of the device, its speaker and microphone are close to each 
other.  Therefore,  due  to  the  application  of  hands-free  mode,  it  may  happen  that  the 
caller  hears  his  own  voice  back  through  the  phone  during  a  conversation.  This  echo 
phenomenon is normal while using the device, therefore it may not be the subject of a 
quality complaint. 
To reduce possible echo phenomenon, there is possibility to adjust the speaker volume 
of  the  device  during  a  conversation  through  DTMF  commands  using  the  keys  of  the 
phone.  By  pressing  intermittently  key  3  on  the  phone  the  speaker  volume  can  be 
decreased, while pressing key 6 it can be increased.

   

2.4.10 SMS forwarding 

The SMS messages received on the SIM card of the device are forwarded automatically 
to  the  phone  number  set  in  memory  section  1.  (This  can  be  used  e.g.  for  forwarding 
pre-pay  card  balance  information  messages  received  from  the  GSM  service  provider). 
If no phone number is set in memory section 1, the device does not forward and deletes 
incoming SMS messages. 

2.4.11 SMS restriction 

The  device  has  built-in  SMS  restriction  function,  which  allows  sending  of  max.  50 
messages per 12 hours (regarding to the sum of the forwarded and alarm messages). 

Содержание gsm easyaid




























Отзывы: