background image

 

4

Event reporting directions: 

 

Event 

T1 T2 T3 T4 S1 S2 S3 S4 

Mon. station 

IN1 

x x x x x x x x 

IN2 

x x x x x x x x 

IN1 

restore 

        

IN2 

restore 

        

Voltage 

low 

    

x x    

Voltage 

restore 

    

x x    

Test 

report 

    

x     

 

T1-T4: 

reporting to 1-4 user phone numbers with GSM voice call 

S1-S4: 

reporting to 1-4 user phone numbers in SMS 

Mon. station: 

reporting to monitoring station with GSM voice call (Contact ID protocol) 

1.4 Functions and parameters 

 

Inputs 

The Compact-GSM module has 2 inputs (IN1 and IN2), which can be activated 
depending on the setting with normally open (NO) or normally closed (NC) contacts wired 
to COM connection point. Sensitivity of inputs is 100ms, which means event is generated 
only if the input is activated for at least 100ms. Alarm monitoring delay is 10 seconds for 
each input, which means if an input is activated, the module ignores new signals on the 
respective input for 10 seconds from activation, so no alarm events are generated in this 
period. When the 10s delay expires, the input becomes available again for activation. 

 

Relay output 

The relay output can be activated by initiating a call to the module’s phone number from 
the 4 user phone numbers using identification of caller phone number, or from any phone 
number without identification, depending on the setting. Relay control mode is 
monostable, activation time is adjustable between 0-9999 seconds. Default setting: 1s. 

 

User phone numbers 

Maximum 4 phone number can be set, where the module sends reports with GSM voice 
call and SMS. The maximum length of the phone numbers should not exceed 16 
characters and international format should not contain “+” character (e.g. 0036….). 
Already set phone number can be erased by pressing the „

#

” key instead of entering a 

new number. 

 

Call and SMS limitation 

The module is equipped with internal call and SMS limitation. The function allows 50 
outgoing calls and sending of 50 SMS messages per day.  

 

Confirmation 

Confirmation of alarms sent to user phone numbers (with GSM voice call) may be 
necessary. In this case the module recalls the number until the user confirms the alarm 
event. If the confirmation function is enabled, then the event can be confirmed by 
pressing „

¾

” key and all alarm events (calls and SMS) in progress can be stopped by 

pressing „

#

” key. By default the confirmation function is disabled. 

Содержание Compact-GSM












Отзывы: