background image

 

3

1 Module operation 

Application areas: can be used as accessory for alarm control panels or as individual 
GSM signaling device with 2 inputs. 

1.1 Functions 

  GSM voice call to 4 user phone numbers on input activation with recordable 

message or siren tone 

  SMS with adjustable text about each event 

  Report to monitoring station with Contact-ID protocol about each event  

  Remote control of relay output with free call 

1.2 Features 

  4 user phone numbers for GSM voice call and SMS 

  SMS forwarding to the first user phone number 

  1 monitoring station phone number for reporting 

  2 NO/NC inputs 

 1 

relay 

output 

1.3 Events 

 

Alarm events 

The communicator initiates GSM voice call with recordable message or siren tone and 
sends SMS with adjustable text to 4 user phone numbers at the effect of input activation. 
At the same time it sends report to 1 monitoring station phone number with Contact-ID 
protocol. Event restoration is sent only to monitoring station. The module tries to perform 
calls and SMS sending on an event for 10 minutes from occurrence, and it stops the 
alarm of this event when time expires even if it fails to communicate to some of the 
phone numbers during this time. Alarm event occurring occasionally during programming 
interrupts programming, hangs up and starts immediately notification process.  

 

Supply voltage monitoring 

The module sends SMS to the first two user phone numbers and report to the monitoring 
station in at most 24 hour interval, if the supply voltage level falls for at least 1 minute 
below 11,6VDC or 23,2VDC, depending on the power source (applying supply voltage 
above 18VDC already means operation on 24V). Event restoration is sent in SMS to the 
same phone numbers, and to monitoring station via GSM voice call. The module does 
not monitor the supply voltage for the first 60 seconds from power up. Low voltage event 
occurring occasionally during programming is notified right after programming is finished. 
Supply voltage monitoring is enabled by default, can be disabled in the settings menu. 

 

Test report 

The module sends test report (alive signal) in adjustable interval in SMS to the first user 
phone number, as well as with GSM call to monitoring station. Time of day for test report 
sending can be set by pressing the program button shortly three times consequently in 
the desired moment. Then the module sends the test report and the following ones are 
sent in the set interval, in the same time of day. When module reset is performed, the 
test report is sent after 3 minutes from reset, and the following ones are sent likewise in 
the set interval. Test report event occurring occasionally during programming is notified 
right after programming is finished. If value 0 is set for this option, the module does not 
send test report. Test report interval default setting is 7 days. 

Содержание Compact-GSM












Отзывы: