Telkom ADSL 5100 Скачать руководство пользователя страница 68

Страница: 68 / 76

The following table describes the labels in this screen.

LABEL

DESCRIPTION

Reset ADSL Line

Click this button to reinitialize the ADSL line. The large text box above then displays

the progress and results of this operation, for example:

"Start to reset ADSL

Loading ADSL modem F/W...

Reset ADSL Line Successfully!"

ATM Status

Click this button to view ATM status.

ATM Loopback Test Click this button to start the ATM loopback test. Make sure you have configured at

least one PVC with proper VPIs/VCIs before you begin this test. The TELKOM

ADSL 5100 sends an OAM F5 packet to the DSLAM/ATM switch and then returns it

(loops it back) to the TELKOM ADSL 5100.

The ATM loopback test is useful for troubleshooting problems with the DSLAM and

ATM network.

Upstream Noise

Margin

Click this button to display the upstream noise margin.

Downstream Noise

Margin

Click this button to display the downstream noise margin.

Back

Click this button to go back to the main

Diagnostic

screen.

Содержание ADSL 5100













































































Результаты поиска

Содержание ADSL 5100

Отзывы:

Похожие инструкции для ADSL 5100

Бренды по названию

Популярные бренды

Telkom ADSL 5100, Инструкция по эксплуатации

Результаты поиска

Содержание ADSL 5100

Отзывы:

Похожие инструкции для ADSL 5100

Бренды по названию

Популярные бренды