Telkom ADSL 5100 Скачать руководство пользователя страница 29

Страница: 29 / 76

messages and is assigned to the permanent group of all IP hosts (including gateways). All hosts

must join the 224.0.0.1 group in order to participate in IGMP. The address 224.0.0.2 is assigned to

the multicast routers group.

The TELKOM ADSL 5100 supports both IGMP version 1 (IGMP-v1) and IGMP version 2

(IGMP-v2). At start up, the TELKOM ADSL 5100 queries all directly connected networks to gather

group membership. After that, the TELKOM ADSL 5100 periodically updates this information. IP

multicasting can be enabled/disabled on the TELKOM ADSL 5100 LAN and/or WAN interfaces in

the web configurator (LAN; WAN). Select None to disable IP multicasting on these interfaces.

4.5 Configuring LAN

Click LAN to open the following screen.

The

follo

wing

table

desc

ribes

the

label

s in

this

scre

en.

LABEL

DESCRIPTION

DHCP

If set to

Server

, your TELKOM ADSL 5100 can assign IP addresses, an IP default

gateway and DNS servers to Windows 95, Windows NT and other systems that

support the DHCP client.

If set to

None

, the DHCP server will be disabled.

If set to

Relay

, the TELKOM ADSL 5100 acts as a surrogate DHCP server and relays

Содержание ADSL 5100













































































Результаты поиска

Содержание ADSL 5100

Отзывы:

Похожие инструкции для ADSL 5100

Бренды по названию

Популярные бренды

Telkom ADSL 5100, Инструкция по эксплуатации

Результаты поиска

Содержание ADSL 5100

Отзывы:

Похожие инструкции для ADSL 5100

Бренды по названию

Популярные бренды