Telit Wireless Solutions GL865 V3 Скачать руководство пользователя страница 69

Страница: 69 / 72

HW User Guide

1vv0301018 Rev. 15

Page

2019-01-07

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Labelling Requirements for the Host device

The host device shall be properly labelled to identify the modules within the

host device. The certification label of the module shall be clearly visible at all

times when installed in the host device, otherwise the host device must be

labelled to display the FCC ID and IC of the module, preceded by the words

"Contains transmitter module", or the word "Contains", or similar wording

expressing the same meaning, as follows:

Contains FCC ID: RI7GL865Q3
Contains IC: 5131A-GL865Q3

L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification

des modules qui s'y trouvent. L'étiquette de certification du module donné

doit être posée sur l'appareil hôte à un endroit bien en vue en tout temps. En

l'absence d'étiquette, l'appareil hôte doit porter une étiquette donnant le FCC

ID et le IC du module, précédé des mots « Contient un module d'émission »,

du mot « Contient » ou d'une formulation similaire exprimant le même sens,

comme suit :
Contient FCC ID: RI7GL865Q3
Contient IC: 5131A-GL865Q3

CAN ICES-3 (B) / NMB-3 (B)

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme canadienne

ICES-003.

Содержание GL865 V3









































































Результаты поиска

Содержание GL865 V3

Отзывы:

Бренды по названию

Популярные бренды

Telit Wireless Solutions GL865 V3, Руководство пользователя

Результаты поиска

Содержание GL865 V3

Отзывы:

Бренды по названию

Популярные бренды