manualshive.com logo in svg

Telit Wireless Solutions BlueMod+S42/AI, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions BlueMod+S42/AI Скачать руководство пользователя страница 55

 
 

 

S42 Hardware User Guide 

1VV0301303 Rev.3 – 2016-08-22  

Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved.
 

 

Page 55 of 62

 

8.2.6 

FCC Labeling Requirements for the End Product 

Any End Product integrating the S42/AI must be labeled with at least the following 
information: 

This device contains transmitter with  

FCC ID:  

RFRMS42 

IC:  

4957A-MS42   

 

8.3 

IC Compliance 

The S42/AI will been tested to fulfill the IC requirements. Test reports RSS-210 of 
Industry Canada are available on request. Grant of the Full Modular Approval is shown 
below. 

The IC Certification is in progress: FCC ID will be 4957A-MS42 

 

8.3.1 

IC Grant 

 

8.3.2 

IC Statement 

(11) 

Ce dispositif doit être installé et exploité dans une enceinte entièrement fermée afin de 
prévenir les rayonnements RF qui pourraient autrement perturber la navigation 
aéronautique. L’installation doit être effectuée par des installateurs qualifiés, en pleine 
conformité avec les instructions du fabricant.  

(ii) Ce dispositif ne peut être exploité qu’en régime de non-brouillage et de non-protection, 
c’est-à-dire que l’utilisateur doit accepter que des radars de haute puissance de la même bande 
de fréquences puissent brouiller ce dispositif ou même l’endommager. D’autre part, les 
capteurs de niveau à propos desquels il est démontré qu’ils perturbent une exploitation 
autorisée par licence de fonctionnement principal doivent être enlevés aux frais de leur 
utilisateur. 

This device complies with Industry Canada license-exempt RSS standard(s).  
Operation is subject to the following two conditions:  

(1) this device may not cause interference, and  

(2) this device must accept any interference, including interference that may cause undesired 
operation of the device. 
 

NOTICE: 

 

This Class B digital apparatus complies with Canadian ICES-003.  

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 

 

Содержание BlueMod+S42/AI































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды