manualshive.com logo in svg

Telit Wireless Solutions BlueMod+S42/AI, Руководство пользователя по оборудованию

Поделиться
Скачать
Telit Wireless Solutions BlueMod+S42/AI Скачать руководство пользователя страница 24

 
 

 

S42 Hardware User Guide 

1VV0301303 Rev.3 – 2016-08-22  

Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved.
 

 

Page 24 of 62

 

Signal 

UICP deactivated 

UICP activated 

UART-CTS# 

I-PD 

I-FLOAT 

IUR-IN# 

I-DIS 

I-FLOAT 

IUR-OUT# 

I-DIS 

O-PP 

Legend: 

I-PD = Input with pull-down resistor, I-DIS = Input disconnected,  

I-FLOAT = input floating, O-PP = Output push-pull 

Signal types I-PD, I-DIS and O-PP may be left open. I-FLOAT has to be driven to GND or 
VCC to avoid open CMOS input oscillation. 

If UICP is deactivated the pull-down resistor on UART-CTS# helps to keep the serial 
interface active if UART-CTS# is open. 

If UICP is active and the serial interface is down, UART-CTS# has to be held at VCC and 
thus the pull-down would cause an unwanted permanent current drain. Therefore the pull-
down is switched off in this mode. 

 

3.4 

GPIO Interface 

It is possible to use the programmable digital I/Os GPIO[0:14] on the S42. Their 
behavior has to be defined project specific in the firmware. 

Unused GPIO pins shall be left unconnected to stay compatible. There may be functions 
assigned to some in future versions of the firmware. 

 

3.5 

I

2

C Interface

1

 

The I

2

C bus interface serves as an interface between the internal microcontroller and the serial 

I

2

C bus. S42 is the master and controls all I

2

C bus specific sequencing, protocol 

and timing. It supports standard (100kHz) and fast (400kHz) speed modes. The 
S42 as an I

2

C master must be the only master of the I

2

C bus (no 

multimaster

 

capability). Clock stretching is supported. 

GPIO[1]/I2C-SDA and GPIO[0]/I2C-SCL can be used to form an I

2

C interface. It is required 

to connect 4k7 pull-up resistors on I2C-SCL and I2C-SDA when this interface is used. 

                                                      

1

 subject to firmware support, contact Telit for current status 

Содержание BlueMod+S42/AI































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды