TeleWell TW-EF600 Скачать руководство пользователя страница 13

Страница: 13 / 133

The Rear Ports

Port

Meaning

Power Switch

Power ON/OFF switch.

Power

Connect it with the supplied power adapter.

Giga Ethernet

Connect to a PC or an office/home network of 10Mbps, 100Mbps or 1000Mbps using the provided RJ-45 Ethernet cables.

RESET

Press this button for more than 5 seconds to restore the device to its
default mode.

WPS
(802.11n Fiber
Optical Router
only)

Push this button to trigger Wi-Fi Protected Setup function.

WAN

specification

100BASE-BX

1000BASE-BX

Ports:
100BASE
Several options for fiber WAN interface and they do not coexist.

Refer to the instructions on the label of the outer box

to of your device.

Port:

A single strand of optical fiber. Single-mode fiber

used (Tx1310nm/Rx1550nm). It supports SC connector.

A single strand of optical fiber. Single-mode

is used (Tx1310nm/Rx1490nm). It supports SC connector.

According to transmission method, the dual fiber

WANS separated into single mode and multi mode.

100BASE-LX/SMF

1000BASE-LX/SMF

Two

strands of optical fiber, one for receive (RX) and the
other for transmit (TX). Single-mode fiber is used
(Tx/Rx1310nm). It supports SC connector.

100BASE-FX/MMF

Two strands of optical fiber, one for

receive (RX) and the other for transmit (TX). Multimode fiber
is used (Tx/Rx1310nm). It supports SC connector.

A cage for SFP (Small Form-Factor Pluggable) transceiver

or 1000BASE optical convector.

Antenna
(802.11n Fiber

Optical Router

only)

Connect the detachable antenna to this port.

Содержание TW-EF600






































































































































Результаты поиска

Содержание TW-EF600

Отзывы:

TeleWell TW-EF600, Руководство пользователя, Страница: 13 / 133

Результаты поиска

Содержание TW-EF600

Отзывы: