Televes 232130 Скачать руководство пользователя страница 7

23

3. Keyboard

The keyboard has only 3 buttons, enough for handling all 

of the equipment’s functions and menus.

The keyboard operation will depend on the working mode.

On top of each button, the fusion splicer screen will display 

the button’s function for the menu in use.

Button

Main functions

 

Turn on / Turn off the fusion splicer, splice 

and push accept selection button

Lower the selection bar highlighted on 

the screen / Access the menu

Take up the selection bar highlighted on 

the screen / Reset

4.  Use

Basic guide

NOTE:

   This is a basic guide to start using the fusion splicer. 

Should you encounter any problems or wish to see 

the processes in detail, please refer to section 7 of 

the manual “Advice for the appropriate handling of 

fibre and tools”.

4.1 Quick start

Turning the fusion splicer on:

                 Connect the fusion splicer to the power supply unit. 

Once connected, the equipment will start automa-

tically. Push any button to exit the charging mode.

                 Make  sure  the  unit  is  charging  correctly.  (Charge 

the unit for at least 6 to 8 hours before using it for 

the first time).

                  Once charged for the first time, bear in mind that 

this equipment allows you to recharge the battery 

while in use.

                 Turn  on  the  fusion  splicer  by  pushing  the  “ON” 

button. The fusion splicer will start in “Ready Mode” 

after a few seconds.

                   (If you wish to change the language of the fusion 

splicer:  Press “MENU”  and  go  to  the “LANGUAGE” 

option by means of the “DOWN” button, push “SE-

LECT” to enter, push “DOWN” or “UP” to select the 

desired language, and finally confirm by pushing 

“SELECT”.

4.2 Single-mode or multimode

When it comes to fusing, selecting the right type of fibre in 

the fusion splicer beforehand is essential. If you are using 

single-mode fibre, for example, select that type of fibre in 

the “Menu”; to do this, follow these steps:

Push  the “MENU”  button. With  the “DOWN”  button  go  to 

“SETTINGS” and push “SELECTION”. Once there, go to “FIBRE 

SELECTION” with the “DOWN” button and select the desi-

red fibre type. Select either “SINGLE-MODE”, “MULTIMODE” 

or “OM1”.

4.3 Calibration

After checking the electrodes, we need to calibrate the fu-

sion splicer in order to adapt it to the work environment 

(temperature, humidity...). (See section 5.2, “Calibration”).

EN

Содержание 232130



















Отзывы: