Teletronics International EZMesh Скачать руководство пользователя страница 20

Страница: 20 / 58

User Guide -

EZMesh Full Duplex Mesh Network Access Point

Note:

The SSID for Client AP(802.11b/g),

“arrow”

, is reserved for a MeshAP Station that

has not associated with(or formed an uplink) with any MeshAP network.

The SSID for Backhaul Radio,

“span”

, is reserved for a MeshAP Station that has

not associated with(or formed an uplink) with any MeshAP network.

This can prevent end users from accidentally connecting to APs that are not part of a

mesh network. They will not get internet access when they connect to APs that are not

part of a mesh network.

Step 2.

Change the PC IP address to

192.168.1.XXX

Subnet mask:

255.255.255.0

Step 3.

Access the MeshAP via

Wireless LAN

Make sure the PC is connected to the SSID:

MeshAP

(The default SSID for MeshAP)

Note:

Please review the Hardware installation Guide for more information.

Step 4.

Open a Web Browser and type

192.168.1.8

to access the MeshAP Access Point.

Step 5.

User Name:

admin

Password:

admin

Click "

TELETRONICS INTERNATIONAL, INC.

- 16 -

Содержание EZMesh



























































Результаты поиска

Содержание EZMesh

Отзывы:

Бренды по названию

Популярные бренды

Teletronics International EZMesh, Руководство пользователя

Результаты поиска

Содержание EZMesh

Отзывы:

Бренды по названию

Популярные бренды