Telemark TVP-2000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 81

Telemark TVP-2000 Скачать руководство пользователя страница 19

Page 19 of 19

TVP Manual (full) March 2007 CE rev 03.doc

Section 2

Installation Guide

Installation

WARNING
The system contains gases under pressure, which may constitute both a frostbite hazard and a
burn hazard.  Refrigerant gases are known asphyxiants and are mildly narcotic.  Precautions
must be taken.  Work must only be carried out by suitably qualified personnel.  Always wear
suitable eye and hand protection.

WARNING
All refrigeration work in which the refrigerant gas is moved or manipulated must be done by a
qualified technician.  Many national laws require individuals who perform such work must have
a certification of Refrigeration Technician.  Other laws in various countries might govern use or
service of this system.  Local regulations should be strictly adhered to.  Particular attention
should be paid to the containment and recovery of refrigerants.

WARNING
The system contains high voltage (either 208 or 415VAC) and high power components.  To
avoid the possibility of a fatal electrical shock always isolate the unit from the mains supply
before working on the system.  A qualified technician should carry out the electrical work.

WARNING
Internal parts of the system may either be very hot, or very cold, presenting a possible burn
hazard.  Always take precautions where the system has been running within the last hour.

WARNING
Read the instruction manual before operation of the TVP Water Vapor Cryotrap.

CAUTION
Do not disconnect, alter or bypass any of the built in safety and protection devices.  This will
void your warranty and possibly increase the risk of equipment damage.

CAUTION
Unit contains pressurised gas.  Do not open hand valves until system is connected to a Cryo-
coil, which has been checked for leaks.  Do not connect the system to other systems unless
their design and application has been approved by the manufacturer, and they have been
assessed for leak tightness.

CAUTION
Do not release refrigerant into the atmosphere it is illegal and dangerous; please refer to your
local authorities instructions regarding the disposal of reclaimed refrigerants.  Read the
Material Safety Data Sheet before installing the system.  Verify compliance to your local
requirements.

CAUTION
Closure of the hand valves whilst the system is at cryogenic temperatures may damage the
valve seats and invalidate the systems warranty.  It must only be attempted on a cryogenically
cold system in the case of an emergency, which is causing gross leakage from the Cryo-coil or
refrigerant lines.

«
...
17
18
19
20
21
...
»

Содержание TVP-2000


















































































Отзывы:

Нет отзывов