manualshive.com logo in svg

Teledyne PIXIS-XF, Системное руководство

Поделиться
Скачать
Teledyne PIXIS-XF Скачать руководство пользователя страница 4

4

PIXIS-XF System Manual

Issue 5

Chapter 5:

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.1

System On/Off Sequences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38

5.2

WinX/32 First Light  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  39

5.3

LightField First Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5.4

Exposure and Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45
5.4.1

CCD Array Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

5.4.2

Exposure Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

5.4.3

CCD Temperature  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46

5.4.4

Dark Charge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

5.4.5

Saturation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

5.5

Readout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48
5.5.1

Full Frame Readout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

5.5.2

Binning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
5.5.2.1

Hardware Binning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50

5.5.2.2

Software Binning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

5.5.3

Output Amplifier {Quality} Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

5.5.4

Controller Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

5.6

Digitization (Rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.6.1

Digitization Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

5.6.2

ADC Offset (Bias)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Chapter 6:

Advanced Topics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6.1

Timing Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.1.1

Free Run {No Response} . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59

6.1.2

External Sync {Readout Per Trigger}. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  60

6.1.3

External Sync with Continuous Cleans {Clean Until

Trigger} Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62

6.1.4

EXT SYNC Trigger Input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  64

6.2

Fast and Safe Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  65
6.2.1

Fast Mode (WinX/32 and LightField) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  65

6.2.2

Safe Mode (WinX/32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  65

6.3

LOGIC OUT Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

6.4

Kinetics Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  68
6.4.1

Kinetic Timing Modes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  69
6.4.1.1

Free Run (Non-Triggered Mode) . . . . . . . . . . . . . . . . . . . . . .  70

6.4.1.2

Triggered Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

6.5

Custom Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
6.5.1

Custom Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
6.5.1.1

Software Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

6.5.2

Custom Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Содержание PIXIS-XF





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды