manualshive.com logo in svg

Teledyne PIXIS-XF, Системное руководство

Поделиться
Скачать
Teledyne PIXIS-XF Скачать руководство пользователя страница 29

Chapter 4

System Setup

29

Host Computer

Computers and operating systems undergo frequent revision. The following 
information is intended to specify minimum computer requirements. Please 
contact the factory to determine your specific needs.

NOTE:

The following requirements are the minimum for operating 
a PIXIS-XF camera. A faster computer with 5 GB or more 
memory (RAM) will significantly enhance software 
performance during live mode operations.

•

WinX Requirements
— Windows XP (32-bit with SP3 or later) or Vista (32-bit)
— 2 GHz Pentium 4 (or greater).
— Native USB 2.0 support on the mother board or USB 2.0 Interface Card 

(Orange Micro 70USB90011 USB2.0 PCI is recommended for desktop; SIIG, 
Inc. USB 2.0 PC Card, Model US2246 for laptop)

— Minimum of 1 GB RAM (or greater).
— CD-ROM drive.
— Hard disk with a minimum of 1 GB available.

A complete installation of the program files takes about 17-50 MB and the 
remainder is required for data storage, depending on the number and size 
of images/spectra collected.
Disk level compression programs are not recommended.
Drive speed of 10,000 RPM recommended.

— Super VGA monitor and graphics card supporting at least 65,535 colors with 

at least 128 MB of memory. Memory requirement is dependent on desired 
display resolution.

— Mouse or other pointing device.

•

LightField Requirements
— Windows Vista (64-bit) or Windows 7 (64-bit)
— 2 GHz  dual  core  processor
— 4 GB RAM (or greater)
— CD-ROM drive
— Super VGA monitor and graphics card supporting at least 65535 colors with 

at least 128 MB of memory. Memory requirement is dependent on desired 
display resolution.

— Hard disk with a minimum of 1 GB available for installation.

Additional space is required for data storage: the amount of space required 
depends on the number and size of images/spectra collected.
Disk level compression programs are not recommended.
Drive speed of 10,000 RPM recommended.

— Mouse or other pointing device.

Содержание PIXIS-XF





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды